sheep
08-30-2008, 01:12 AM
well since there arent too many How-Tos in this section yet i might as well add this one since i have seen many other forums have it but yet to see it on here anywhere
i am going to run through the steps to seafoam the oil, gas, and brake master cylinder line. if you have never heard of seafoam here is a link to thier website: http://www.seafoamsales.com/motorTuneUpConsumer.htm
personally i use it in my gas tank and master cylinder line, i havent tried it in my oil yet just becuz i have been told to change your oil soon after using it, not sure why, i just havent gotten around to the end of a oil change yet to add it.
i know this works from personal experience and the 100s of people that i have talked to on this and different sites that have also had it work.
things you will need:
1: can of seafoam motor treatment(can be found at any autoparts store, and walmart)
2: small cup
3: a friend that can follow simple instructions
step 1 adding to oil(optional):
1: add 1/3 can of seafoam to oil
2: drive for probably a good 100-300 miles
3: change oil, make sure you let it drain all out!
step 2 adding to gasoline:
1. add 1/3 can of seafoam to gas tank
your done!
step 3 running it through master cylinder vacume hose
1. 1/3 can of seafoam in small cup
2. remove vacume hose from master brake cylinder
3. have buddy start the car and hit the gas while you Pour the seafoam in slowly
4. as soon as cup is empty shut off car and wait 10min
5. start car and rev engine and watch all the white smoke poor out the back
6. after a few min of reving the engine drive the car around for a few miles while letting the RPMs get high
after this your car should run a bit better, this might not work as well on newer vehicles becuz they havent had 150k miles to build up a bunch of crap in there but it couldnt hurt anything i dont think.
if i missed anything feel free to PM me and ill add it
i am going to run through the steps to seafoam the oil, gas, and brake master cylinder line. if you have never heard of seafoam here is a link to thier website: http://www.seafoamsales.com/motorTuneUpConsumer.htm
personally i use it in my gas tank and master cylinder line, i havent tried it in my oil yet just becuz i have been told to change your oil soon after using it, not sure why, i just havent gotten around to the end of a oil change yet to add it.
i know this works from personal experience and the 100s of people that i have talked to on this and different sites that have also had it work.
things you will need:
1: can of seafoam motor treatment(can be found at any autoparts store, and walmart)
2: small cup
3: a friend that can follow simple instructions
step 1 adding to oil(optional):
1: add 1/3 can of seafoam to oil
2: drive for probably a good 100-300 miles
3: change oil, make sure you let it drain all out!
step 2 adding to gasoline:
1. add 1/3 can of seafoam to gas tank
your done!
step 3 running it through master cylinder vacume hose
1. 1/3 can of seafoam in small cup
2. remove vacume hose from master brake cylinder
3. have buddy start the car and hit the gas while you Pour the seafoam in slowly
4. as soon as cup is empty shut off car and wait 10min
5. start car and rev engine and watch all the white smoke poor out the back
6. after a few min of reving the engine drive the car around for a few miles while letting the RPMs get high
after this your car should run a bit better, this might not work as well on newer vehicles becuz they havent had 150k miles to build up a bunch of crap in there but it couldnt hurt anything i dont think.
if i missed anything feel free to PM me and ill add it