Search:

the mods look great

- - - Updated - - -

Well it was actually earlier this week, but I did an oil change. Then decided to to a front end inspection. Expected to find the ball joints to be worn...

There are a variety of cans at each place you go (Walmart, napa, autozone etc) so if you go to Walmart there will probably be two or three types. I believe most have sealers in them as you typically...

A can may do it if its low but if its low there is usually a leak. Otherwise it will overcharge it. Doesn't hurt to grab a can.

Windmills and solar was a lot of what I was talking about with billions to prop up an industry, but ethanol was heavily subsidized initially, and no conspiracy theories here (wasn't trying for a full...

Is the world going to end from it? Nope, but that being said I do have a problem with most crap the govt. pushes. Call me one of those whacko free market principle kinda guys. If the govt has to...

Unfortunately I would say replace. If you bend back you will weaken the bolt

I'm not sure why its mostly been vw doing the tdi (even though they stopped for a while). Great gas mileage enough get up and go for a car. Small diesels should be more common IMHO. You can also get...

As stated you will want to find the leak. So use one with a dye. Hey will all have pressure gauges. One thing first, see if the compressor clutch is turning on. If too low or too high the clutch...

I've been real busy and have only been able to pop in and out, which I guess is why I didn't realize there was Steve/surrealone issue. Hopefully it's not a permaban and he comes back as he will be...

My 2013 specifically states to not use anything over E10 on both the cap and manual. Warranty says not using approved fluids will void warranty. So it's not just pre 2012

You could try a junkyard/dismantler. Get the part number from the dealer then google search that part specifically. Check gmpartsclub.com (site vendor)

Craigslist or a small tire shop.

Glad to help, even though I grabbed it from a website:). I've done is liar things with the MAF. I have left it disconnected once on two different vehicles. On the car it was noticeable immediately....

So after your guys help and after reading a good discussion on another forum I think I am going to go back to the mechanical pump. Weighing pros and cons of each I think its a little easier, plus I...

If I mention it was my birthday on the 7th will that get me a few extra votes:rofl::lol:. As stated earlier good luck all and as always great looking trucks.

Thats great to hear.

Looks good so far

Very nice. Hopefully you can chase down the issue

this is how it's currently set up. I found a 4 psi pump for about the same price as an OE style mechanical, but wasn't sure if that was enough psi, the next was 6 psi but almost double the cost.

...

the electric pump is a simple single line with no return (I'm not sure when the electric pump was put on, at least 14 years ago. That being said its probably only got a few hundred miles on it in...

I would think that if thats what the manual states you will be good. When did they even start using the Autotrak? Maybe the 1996 is pre autotrak fluid.

For some people smarter than me. Now I know that this is technically on a 1960 Land Rover Series II 88, BUT the fuel pump is feeding a single barrel Holley for a 60's GM Truck inline 6, that and...

I am planning to add the Tru-cool cooler, but as @mfleetwood and 99'HEARTBEAT stated the cooler is/was replacing an already factory installed transmission cooler. Maybe that has something to do with...

Since those are lean codes also look at the MAF. I know with my aftermarket Granetelli MAF (supposedly designed for cold air intakes) those are the codes that I will throw sometimes if coasting down...

Usually I hate getting stuff at the stealership too but when I went for the autotrak fluid the price/qt was actually similar in price as any decent synthetic fluid.