GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: Zabob44

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    1,176

    I am have a 2002 2wd 5 speed.that i just changed...

    I am have a 2002 2wd 5 speed.that i just changed tire size on the computer..with a tech 2 go under chassis and special functions and you can change your tire size..not sure that it goes all the way...
  2. Thread: 94 burban

    by Zabob44
    Replies
    13
    Views
    1,304

    Agreed, and corrosion on your throttle body? You...

    Agreed, and corrosion on your throttle body? You mean Carbon build up?
  3. Replies
    7
    Views
    910

    There is almost no chance that this had anything...

    There is almost no chance that this had anything to do with the tire pressure sensors. By reset do you mean relearn the location?
  4. Replies
    13
    Views
    4,120

    It take more power to separte the hydrogen from...

    It take more power to separte the hydrogen from the water than what you would get in return..I wouldn't put it on my truck. I could spend $1000 on something fun, or just gas.
  5. Replies
    16
    Views
    7,081

    sounds like a combination switch problem to me...

    sounds like a combination switch problem to me then
  6. Replies
    16
    Views
    7,081

    Maybe your getting back feed power from something...

    Maybe your getting back feed power from something else..have you looked at a diagram to see what else is fed off that circuit? Check power at the relay maybe your just getting partial voltage from...
  7. The two wires are probably power and ground and...

    The two wires are probably power and ground and the others are the different resistances for the blower motor setting..maybe there are more wires up there you can't see..haven't done one...
  8. Not sure right off..I will check tomorrow at work...

    Not sure right off..I will check tomorrow at work if I get a minute to see if there is a spec for that.
  9. ohms is the upside down U looking shape in case...

    ohms is the upside down U looking shape in case you didn't know..not sure of an exact spec but shouldn't be too much and if it's bad it will probably have an open in it and read very high if it...
  10. Replies
    6
    Views
    3,050

    couldn't of said it better myself

    couldn't of said it better myself
  11. Replies
    14
    Views
    2,397

    yeah, I like to think about the time the guy...

    yeah, I like to think about the time the guy working there flushed the power steering fluid instead of the trans fluid...good times.
  12. Replies
    4
    Views
    850

    I don't get what your concerned with? Where to...

    I don't get what your concerned with? Where to put the sub and amp or cutting into the speaker wire?
  13. Replies
    14
    Views
    2,397

    If your towing it isn't bad to change it once a...

    If your towing it isn't bad to change it once a year..personal preference I guess.
  14. Check resistance in the sensor..but the trans...

    Check resistance in the sensor..but the trans would prob. read the VSS sensor before the others
  15. Replies
    8
    Views
    1,192

    If it is that would probably be your best bet....

    If it is that would probably be your best bet. There isn't much to test without taking out the cluster, and if its under warranty let the dealer do it.
  16. Replies
    8
    Views
    1,192

    could even be a bad cluster. what year? under...

    could even be a bad cluster. what year? under warranty?
  17. Replies
    8
    Views
    1,192

    I think you would see it in more than just the...

    I think you would see it in more than just the Cluster. if it was the battery like the radio display lights would flicker too. And while your driving your car the battery doesn't do much other than...
  18. Replies
    8
    Views
    1,192

    Hmm..I would almost think it has to be a wiring...

    Hmm..I would almost think it has to be a wiring issue, I guess it could be a programming problem, and needs to be reflashed. Had any work done lately? You could prob. try and take out the i/p and...
  19. Replies
    8
    Views
    1,192

    Wiring behind cluster has rubbed through...

    Wiring behind cluster has rubbed through somewhere or come unplugged? Not sure if it's a common issue. Does it happen over bumps?
Results 1 to 19 of 19