Type: Posts; User: SuburbanSS
Search: Search took 0.00 seconds.
06-14-2010, 02:56 AM
Hey all, guess there was a little bit of confusion on the universal app light bar, each application has its own unique mounting kit that is sold seperately, his would be for just the safari light...
06-11-2010, 10:11 PM
Hey just got all settled in.
I have sold all the programmers, I still have the rims and the light bar. If you are still interested in either of them let me know.
I would take $75+ship for...
05-30-2010, 09:50 AM
Most of this stuff was left with my brother in his storage, but if you are interested I can have him ship it out.
Still have the following:
Westin Safari Light Bar 30-0000...
I'm going to step out on a limb here and take am educated guess. It sounds as though the refrigerant pressure is low, causing the A/C Compressor not to kick in, sometimes it can prolly build enough...
Have a new issue with my folks '96 Tahoe 4x4 w/ 4L60E Transmission.
I was heading back down from NH and I got up to highway speed without an issue, stopped and started getting up to...
Well, I decided to take a leap of faith with no other real option I grabbed the first thing that closely mimicked a yoke puller I could find aka Old school 1960's Snap-On harmonic balancer puller...
So in a worse case scenario if I were forced to replace the rear yoke, is it as simple as pulling it out and replacing it, or would anyone know if these have a crush sleeve I would need to worry...
Another quick repair that turns into a project. Ahh, the fun never ends...
I have a 1996 Chevy Tahoe that needed u-joints replaced but of course in the process of taking off the retaining clips...
I have 1 out of 3 power ports that work whereas the other 2 do not. However I was unable to find any blown fuses.
I guess I will have to try unplugging the two that do not work and see if they are...
I have a 1996 Chevrolet Tahoe 4WD w/ 5.7L and the ODB-II port doesn't seem to want to interact with any ODB-II scanner that is attached to it, running or in ON position.
I was then...
11-24-2009, 12:55 PM
So I've been working on this project truck for awhile and still have some sort of power issue..
I have freeze frame data and a few DTCs but nothing that seems to be big issues.
I tested power supply to the connector and verified the 5v supply it should be getting was right at 5.01, and in terms of testing vacuum what would be the best method of testing it, hooking up a...
I have a problem where it seems like the truck is pulling a 20,000lb trailer and it has absolutely no power.
Basically an almost full overhaul:
Recently rebuilt Motor & tranny....
So a buddy of mine threw the truck on his 3grand Snap On code reader and it shot out over 10 codes, so he cleared them and they instantly back, the code reader was stating that it was 16 degrees...
Well yesterday I cleaned the MAF sensor with MAF Cleaner, didn't seem to do much.
Will try regapping the plugs and see what that does and go from there...
From what I can tell the MAF is...
Well we put a compression tester to the #1 cylinder and burst cranked till we got it to the compression stroke and then tweaked the pulley till the timing mark lined up on the harmonic balancer then...
It currently has a brand new distributor, ignition coil, crankshaft position sensor, ignition control module, new fuel pump, fuel filter, bosch platinum plugs (gapped at .060 currently - would that...
Took a look around looks like its just a hose for the brake booster from what I can gather for hoses, so it appears everything is in order, I guess the next thing is to put a scanner to it and see...
The following is in reference to a 1998 Chevy Suburban C1500 5.7 2WD
So we got the olde girl fired up and driving and now it lacks power big time while accelerating.
And now to the best of my...
06-29-2009, 08:10 PM
So I figured I'd give you all an update:
There was a harness in between the bell housing and engine that was popping the fuse ( score 1 for capt. obvious ) but we got it all fixed and started up,...
Bigwheels.net they have a very big selection as well as pairing up just about any rubber you want with it as a package.
There are plenty around and roughly will provide all the same gains as far as a Gas motor goes, the real way to go is to actually have your VCM custom tuned if you have any upgrades done they will...
06-15-2009, 10:58 PM
So threw another 5hrs at it today trying to trace the wiring that makes up the ECM-B fuse.
Disconnected all harnasses associated with the ECM-B fuse, fuel pump, oil pressure sensor (which was the...
06-14-2009, 09:01 PM
Well to clarify a bit I didnt start replacing ignition component parts till after we had established there was no spark. we pulled the plug & wire from cylinder one and checked for spark by leaving...
06-14-2009, 08:19 PM
So I started around 9am after the guy that is helping me put in my new rebuilt tranny in my 1998 Chevy Suburban.
After he finished putting the tranny in went and connected the battery back up and...
Results 1 to 25 of 49