GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: a.graham52

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    89
    Views
    36,494

    iv been on it since 09. helped me out a ton with...

    iv been on it since 09. helped me out a ton with the alero.
  2. Replies
    89
    Views
    36,494

    Hey are u a member of aleromod.com ?

    Hey are u a member of aleromod.com ?
  3. Replies
    7
    Views
    1,698

    since when has a clutch worked of the brake...

    since when has a clutch worked of the brake system? at most iv seen them share resivours (both use brake fluid) but nothing after that is shared. the clutch is its own system with its own master,...
  4. Replies
    11
    Views
    1,342

    depends on what code sets or what sensor fails....

    depends on what code sets or what sensor fails. if maf or o2 sensor (etc) fails then yes its stuck in open loop because it NEEDS those sensors to be in closed loop. if its just an evap code setting...
  5. the usual tell of a bad sensing unit is it goes...

    the usual tell of a bad sensing unit is it goes from being accurate to inaccurate a lot. if the gauge is just dead, it MAY be a nother problem.
  6. Replies
    10
    Views
    1,579

    a lot of the time once you get the manifold off,...

    a lot of the time once you get the manifold off, you find the bolt is sticking out of the head, take "stud grippers" or stud remover like mantioned above and usualy they come right out. 9 times out...
  7. Replies
    3
    Views
    717

    there is actually a bulletin for replacing the...

    there is actually a bulletin for replacing the vent valve. these year trucks (and a few other years) came out with a vent valve with build in filter. problem is they would stuck in dirt. the new...
  8. Replies
    3
    Views
    717

    sounds like a stuck vent valve. common problem on...

    sounds like a stuck vent valve. common problem on them trucks. check engine light?
  9. Replies
    2
    Views
    645

    I had reinstalled the PCV system yesterday when...

    I had reinstalled the PCV system yesterday when did intake gaskets. O2 sensor new 20k ago as we'll as the electric injectors (x engine). Fuel pressure seems to be within spec (for the x engine)....
  10. They press on and off. Is the noise load...

    They press on and off. Is the noise load sensitive (more or less throttle) if it is then its probably just wear on the ring and pinion. Only way to cure that is to replace the ring and pinion.
  11. Replies
    2
    Views
    645

    2002 Sierra 4.3 high fuel trims

    At cruise my LONG TERM fuel trims are +9,any other time (idle, wot) their around +3.

    Truck mods are:
    Trimmed butterfly (currently has stock I stalled)
    K&N filter (tested with stock paper)...
  12. anyone want to share an EFI live tune for a 4.3?

    as the title says, im hoping a few people would have a 4.3l EFI tune they would like to share. the shop i go through has a lot of of tunes for 4.8+ but this is the first 4.3 hes done. hoping to get a...
  13. Replies
    3
    Views
    565

    I have the really and a harness already...

    I have the really and a harness already installed. I dot know what wire needs to b added to the PCM to ground the control side of the relays
  14. Replies
    3
    Views
    565

    e-fan wiring for 02 4.3l

    i must have missed it in my search, i had my ECM reprogramed for electric fans on my 02 4.3 k truck. they guy who did the programing was not able to tell me which to terminals on the ecm need to be...
  15. Replies
    0
    Views
    288

    02 4.3 loosing timing?

    So I noticed today when pulling a hill from a stop and merging into traffic, 1st and 2nd pulls great. 3rd 4th and 5th lacked power pretty bad. My ultra-gauge showe engine timing going from almost...
  16. Replies
    5
    Views
    568

    It's just a minor oil leak at the back of the...

    It's just a minor oil leak at the back of the intake. I'm just assuming if oil is coming out, air must be going in. And I do t want to do I take gaskets Again so soon
  17. Replies
    5
    Views
    568

    iv got vaccume leaks at the dipstic, distributor...

    iv got vaccume leaks at the dipstic, distributor gasket and possibly the back of the intake. i know how the system works and everything i just wasnt sure if somone has removed it from the intake...
  18. Replies
    5
    Views
    568

    PCV mod questions

    id like to eliminate my PCV system (from my intake) so i can keep my intake clean and also reduce the small vac leaks i have. iv tested this with both parts of the intake plugged and my fuel trim...
  19. Replies
    5
    Views
    684

    ill check it out. i think i found the problem...

    ill check it out. i think i found the problem though. i removed the IAC and cleaned/lubed it and stuck it back in. havnt had any issues in 4 days.
  20. Replies
    5
    Views
    684

    The tb is clean, and I sprayed around the intake...

    The tb is clean, and I sprayed around the intake with carb cleaner and no leak appeared. The only thing I haven't got a possitive idea of is the back of the block. I'll have to look at that tomorrow.
  21. Replies
    5
    Views
    684

    cold start idle hunt

    i have a 2002 gmc sierra with a 4.3L 5spd. on some cold mornings ill start it from a cold soak over night and the idle will hunt quite a bit. go from 900 to 300 and back and forth over and over for...
  22. id want an early 80s pickup for the bigginning....

    id want an early 80s pickup for the bigginning. fuel will be plentiful for a little while so it shouldn't be too bad. upfit it with a rugged brushgard on front, modified steel tube rear bumper. id...
  23. Replies
    3
    Views
    1,143

    rearch hypermiling. the biggest thign you can do...

    rearch hypermiling. the biggest thign you can do is adjust your driving habits. which will only magnify power mods when it comes to mpgs.
  24. After thinking about It I'd like tj take the last...

    After thinking about It I'd like tj take the last half of my statement back haha. So the only way to get the bind is by having the transfer case engaged right?
  25. i thought auto 4x4 worked by leaving the front...

    i thought auto 4x4 worked by leaving the front diff engauged (right axle shaft locked together) and then the trasfcase was 4x4/4x2 engaged as nessary? i belive if your front diff is engauged rather...
Results 1 to 25 of 211
Page 1 of 9 1 2 3 4