GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: Looey

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    7,804

    thanks! all the best to you in 2013!:) Leo...

    thanks! all the best to you in 2013!:)

    Leo
    London, ON
  2. Replies
    20
    Views
    7,804

    well, 2012 racing season came and went...best I...

    well, 2012 racing season came and went...best I could do was 8.74 at 154mph. Decided not to spray it to get that 7.99. It's not the engine's fault that it is too small..lol.
    I've decided that for...
  3. Replies
    20
    Views
    7,804

    Ready for 2012....looking for a 7.99.... 35722

    Ready for 2012....looking for a 7.99....

    35722
  4. Replies
    2
    Views
    887

    Ok, I'll ask it....did you check the oil level?

    Ok, I'll ask it....did you check the oil level?
  5. Thread: Gas Gauge

    by Looey
    Replies
    8
    Views
    848

    You are probably right. Even after they replaced...

    You are probably right. Even after they replaced the pump the truck wouldn't start. It turns out that over the course of the truck's life before I owned it, someone had probed the wires for the pump...
  6. Thread: Gas Gauge

    by Looey
    Replies
    8
    Views
    848

    The gauge was fine until I had to have the fuel...

    The gauge was fine until I had to have the fuel pump replaced 3 years ago. I should check the diagrams but I'm too lazy and I was hoping somebody else had the easy fix!:)
  7. Thread: Gas Gauge

    by Looey
    Replies
    8
    Views
    848

    When I put the cruise on it really goes for a...

    When I put the cruise on it really goes for a spaz!
  8. Thread: Gas Gauge

    by Looey
    Replies
    8
    Views
    848

    Not to hi-jack the thread, but here goes...my '99...

    Not to hi-jack the thread, but here goes...my '99 Yukon gas gauge looks as if it is vibrating whenever the ignition is on. Ideas?
  9. Replies
    108
    Views
    9,575

    you think twin I beams are really bright...

    you think twin I beams are really bright headlights
  10. You should check the ignition timing. You have to...

    You should check the ignition timing. You have to disconnect the timing plug which is located on the passenger side firewall along with the relays. It should be set at 0* with the plug disconnected.
  11. Replies
    12
    Views
    4,209

    What is your location? I know of a shipping depot...

    What is your location? I know of a shipping depot at the Port Huron/Sarnia border.
  12. Replies
    108
    Views
    9,575

    your truck came with a bicycle

    your truck came with a bicycle
  13. Replies
    4
    Views
    1,264

    My seat heat only works if the seatbelts are...

    My seat heat only works if the seatbelts are connected, but it's a '99.
  14. Replies
    5
    Views
    2,717

    Piston slap. There is nothing you can do about...

    Piston slap. There is nothing you can do about it, and it's probably harmless....
  15. Thread: HID issues...

    by Looey
    Replies
    16
    Views
    1,753

    Had the same issues. I put a relay in so that the...

    Had the same issues. I put a relay in so that the wire coming from the headlight switch only activated the relay, and the power for the hids, came directly from the battery. Also, run the ground wire...
  16. Replies
    9
    Views
    4,871

    put the AC delco's back in there and weld the...

    put the AC delco's back in there and weld the hood shut!:)
  17. I googled high HC and copied it here....some...

    I googled high HC and copied it here....some interesting reading....


    Just a reminder of what causes different emissions readings and what to do about them--

    A high HC reading is the result...
  18. Replies
    6
    Views
    1,616

    Welcome! Has the fuel filter ever been replaced?...

    Welcome! Has the fuel filter ever been replaced? I would start there. Go with the easy stuff first...:)
  19. Thread: 1990 1500

    by Looey
    Replies
    43
    Views
    2,202

    Unfortunately your tbi manifold won't bolt up to...

    Unfortunately your tbi manifold won't bolt up to a vortec head. But! You can bolt the tbi on any sbc (gen 1, 305,327,350,400) as long as the cylinder heads aren't so old that they don't have the...
  20. Replies
    12
    Views
    1,070

    Charlie, with all due respect, I'd rather spend...

    Charlie, with all due respect, I'd rather spend my time looking for a good machine shop, than trusting what comes in a crate. The machine shop business is alive and well. Just sayin'...:)
  21. Replies
    35
    Views
    3,549

    I didn't read all the posts, if it only happens...

    I didn't read all the posts, if it only happens going over bumps it could be the tailgate.
  22. Replies
    12
    Views
    1,070

    My .02... Take that TBI 350 to a reputable...

    My .02... Take that TBI 350 to a reputable machine shop. Have it rebuilt. Put this camshaft in it compcams K12-256-. Don't forget to add GM Engine oil supplement with zinc (flat tappet camshafts...
  23. Replies
    8
    Views
    1,120

    There is probably ice/snow built up inside the...

    There is probably ice/snow built up inside the wheel throwing the balance off. Been there, done that!:)
  24. Replies
    11
    Views
    1,537

    I have a 99 Yukon with the 5.7 vortec. As the...

    I have a 99 Yukon with the 5.7 vortec. As the ambient temps go down, so does the fuel economy. I think it's because the engine is always getting cold air and the ECM keeps pouring the fuel to it....
  25. Thread: ok new problem

    by Looey
    Replies
    9
    Views
    626

    Double check that the spark plugs are the right...

    Double check that the spark plugs are the right ones. You did use AC delco's right?:)
Results 1 to 25 of 75
Page 1 of 3 1 2 3