GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: kw70chevy

Page 1 of 4 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    4
    Views
    819

    might check with napa auto parts they may carry...

    might check with napa auto parts they may carry them in a kit. measure across where the bar go,s see if they are close.
  2. Replies
    6
    Views
    1,137

    there is a little black box on the fender weld...

    there is a little black box on the fender weld next to the battery box there should be a wire coming off of it that hooks to the positive side of the battery if its not hooked up the truck want turn...
  3. Replies
    4
    Views
    819

    they should have the bar in them. my 77 k10 has...

    they should have the bar in them. my 77 k10 has them my78 k20 had one
  4. Replies
    2
    Views
    887

    my coworker has a 70 model with a in line 6 i...

    my coworker has a 70 model with a in line 6 i will see what the bracket looks like if it is the same 0n a old v8 i might have one

    - - - Updated - - -

    they have pic on google for the alt and...
  5. if it was me i would put a electric fuel pump on...

    if it was me i would put a electric fuel pump on it.
  6. have you tried taken the fuel pump.connect a hose...

    have you tried taken the fuel pump.connect a hose to it. stick it in a gas can to see if the pump picks it up.if it does. you have one of the hoses crossed on the sending unit.
  7. Replies
    493
    Views
    21,597

    empty pockets

    empty pockets
  8. Replies
    13
    Views
    2,856

    did you bleed the brakes after you changed your...

    did you bleed the brakes after you changed your caliper.your old caliper most likely was not the problem the rubber brake hoses colapse on the inside and want let the pressure off causeing the...
  9. gotter done

    gotter done
  10. Replies
    4
    Views
    764

    had a 3/4 ton just like it my 14 bolt rear end...

    had a 3/4 ton just like it my 14 bolt rear end was bullet proof if you do change it to eight lug all you have to do to the front is change the rotors its all the same spindels as the half ton
  11. Replies
    2
    Views
    1,665

    two bolts behind the door one under the bottom...

    two bolts behind the door one under the bottom some under the fender weld and some behind the head light
  12. Replies
    8
    Views
    2,760

    the blower motor may be pulling to many amps

    the blower motor may be pulling to many amps
  13. Replies
    1
    Views
    794

    jack one side of your front tire up at a time...

    jack one side of your front tire up at a time move your wheel side to side to see how much play you have look underneath to see if your pitman arm has slack in it or if it is in the tie rod ends....
  14. Replies
    7
    Views
    2,264

    change your door hinge pins before you take it to...

    change your door hinge pins before you take it to the dealer. you can get them at the auto parts store.the bushing wear out and cause the door to sag.
  15. Replies
    12
    Views
    2,195

    got his money worth out of them

    got his money worth out of them
  16. Replies
    6
    Views
    1,011

    either your comp is bad or your dryer is bad if...

    either your comp is bad or your dryer is bad if your compressor was good i would change the dryer the sack in side may have colapsed.
  17. Replies
    8
    Views
    2,760

    the fan switch does go bad.

    the fan switch does go bad.
  18. Replies
    6
    Views
    1,011

    may be over charged let some freon out if they...

    may be over charged let some freon out if they are over charged they will not cool.bring it down to 45 on the low.
  19. Replies
    4
    Views
    676

    i looked at my surburb that wire hooks in the big...

    i looked at my surburb that wire hooks in the big wire loom at the firewall right next to the wires where the wiper moter wires run look in the loom see if that white wire is there.
  20. Replies
    3
    Views
    1,066

    they have nuts on top its kind of tight fit but...

    they have nuts on top its kind of tight fit but you can get a wrench on them
  21. Replies
    6
    Views
    1,432

    ive never messed with rear disc.if the brake is...

    ive never messed with rear disc.if the brake is draging looseing up the bleeder screw.if it releases then change your brake hose some times they colapse. and they want release.
  22. Replies
    9
    Views
    1,640

    check your exhaust pipes make sure they are not...

    check your exhaust pipes make sure they are not rubbing against something
  23. Sticky: A woman gets on a bus with her baby. The bus...

    A woman gets on a bus with her baby. The bus driver says ,"Ughh, That's the ugliest baby I've ever seen!" The woman walks to the rear of the bus and sits down, fuming. She says to a man next to her...
  24. Replies
    9
    Views
    2,607

    if it is a throttle body look on the pass side on...

    if it is a throttle body look on the pass side on the throttle body there is a about a 15/16 nut on the side un screw it it has a spring valve in it it gets gummed up it will mess up the idle clean...
  25. Replies
    7
    Views
    1,646

    only thing on the drivers side by the rad is the...

    only thing on the drivers side by the rad is the condensor.
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4