GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: Hummer

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Update, I have now run two tanks of gas through...

    Update, I have now run two tanks of gas through the 2500 and not the first clunk. Keeping my fingers crossed though haha. Thanks again guys.

    The moly powder in the power steering unit is also...
  2. Many thinks to Pikey and Skinner for the fix with...

    Many thinks to Pikey and Skinner for the fix with the grease fitting.

    I decided to follow their lead instead of what I proposed above.

    The fittings I got from NAPA 715-2003 were 1/4X28 TPI...
  3. From the pics I am looking at there seems to be a...

    From the pics I am looking at there seems to be a screw in the shaft which I am assuming keeps it from coming off? Am I right if this screw is removed the shaft will come apart?

    If that is the...
  4. It steers just fine and steering feels "tight"...

    It steers just fine and steering feels "tight" and by this no lost motion or play. Ball joints were checked and they are fine.

    I talked with my friend today and we are going to try to replace the...
  5. The shop that told me this normally has a...

    The shop that told me this normally has a excellent rep. The rebuilt assembly we are getting is from Advance which has a lifetime warranty as long as I own the truck which I can assure all will be a...
  6. Steering box failure 2500HD appears to have a serious problem.

    I started getting clunking noises hitting bumps etc and we found the pivot pin assembly had vertical movement about 1/2" so we replaced that.

    Then multiple clunks (different than before) started. ...
  7. I too have not heard of them but got to admit...

    I too have not heard of them but got to admit they sure look good. Thanks much for info.
  8. Replies
    5
    Views
    1,120

    Apparently the membrane/splash guard is critical....

    Apparently the membrane/splash guard is critical. Talked to an A1 tranny guy and he said not to remove membrane but to hold it up like it came from factory.

    I used a couple clips and clamped it up...
  9. Replies
    5
    Views
    1,120

    I bought bumper through realtruck.com. Do a...

    I bought bumper through realtruck.com. Do a search for Boondock and it will come up. I talked to the factory guy and he said he only has one dealer on east coast but plenty from Oklahoma to west...
  10. Replies
    5
    Views
    1,120

    GMC Tranny temperature question

    I have a GMC 2500HD WT Classic Body Style w/ the 6L engine and I love it.

    About two months ago I hit a deer coming home on left front and bent the bumper which was right at $1000.00 to repair. ...
  11. Adding additional LED STOP, TAIL, & TURN light question

    LED lights are THE THING for emergency lights. I have a 2007 2500 Sierra HD that I put a camper shell on. I am a firefighter and wanted to add additional LED lighting for safety so I got Maxxima...
  12. No, it showed the assembly opened and how the...

    No, it showed the assembly opened and how the resistors were put in circuits with pictures. Mine has 4114 bulbs and I have checked four sources and no one has a regulator circuit built in to handle...
  13. Replies
    4
    Views
    913

    Just put in Steve for the address? Seems too...

    Just put in Steve for the address? Seems too simple.
  14. Converting Daylight Running Lights to brighter LEDs

    When I first joined the GMTC there was a thread about how a guy converted his DRLs to LED and I think he put a resistor in the line to lower the voltage as I remember the voltage for the 4114 was too...
  15. Replies
    4
    Views
    913

    How do I contact the administrator

    I just sent a PM to administor and it got bounced. I have a complaint and can't find who to complain to.
  16. Thread: Amber DRLs

    by Hummer
    Replies
    7
    Views
    3,963

    About 18 months back there was a nice article...

    About 18 months back there was a nice article about converting the 4114 DRLs to LED and the guy cut a power wire and put in a resistor to cut the voltage. I tried to find it on a search but no luck. ...
  17. In researching this further I have found some...

    In researching this further I have found some excellent lights for run/turn. Truck-Lite 22202Y are extremely bright in the turn mode and normal in the run mode and are also available in RED. They...
  18. I have seen the replacement bulbs for 1156/1157...

    I have seen the replacement bulbs for 1156/1157 bulbs mounted to give 360 degree. The ones I have don't seem to have 30 deg but then again don't have any easy way to measure such.

    Just eyeballing...
  19. I just saw some the other night while researching...

    I just saw some the other night while researching lighting and they were driving lights designed to be mounted on round tubing but I forget where I saw it. The outfit made lights for ambulances as...
  20. Found out interesting fact about LED lights and how to mount them correctly.

    While researching LED lights I have learned they need to be mounted so they emit light more or less parallel with the road surface as they are restricted to about 10 degrees of maximum viewability. ...
  21. Want to add extra run and turn signal light question.

    Got a GMC 2500HD 2007 Classic body style. Just had a fiberglass shell put on with Maxxima LED red strip lights(about 15" long each side) on the to the shell to double as brake lights and extra...
  22. Replies
    4
    Views
    755

    Think I found the right combo and appears to be...

    Think I found the right combo and appears to be affordable.

    http://www.class8truckparts.com/TruckLite-Model-22-Side-Turn-Light/M/B001MQ3R38.htm

    They are marker and turn and pull 2.1 amps in...
  23. Replies
    4
    Views
    755

    The red strip lights are about 1 1/4"X 12" and...

    The red strip lights are about 1 1/4"X 12" and are surface mount thus they point outwards 90 deg to mount surface. I estimate the back of the shell has about a 30 deg forward tilt to it so lights...
  24. Replies
    4
    Views
    755

    Extra amber lights on rear needed

    Just got a fiberglass truck cap for 2500 HD and wired in LED strip lights for run/stop. (3 wire hook up- 1 in ground). Was thinking of putting on more amber lights on shell so when 4 way...
  25. Confusing GMC Owners manual on engine oil requirements.

    Just sold my 2003 Silverado as I needed a 3/4 ton for serious travel trailer towing.
    I ran Mobil 1 10W30 in Silverado as it said at temps above zero to hotter than hell it was fine. In temps to...
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4