GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: Scott77

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,490

    Happened to me a couple months ago, was a check...

    Happened to me a couple months ago, was a check code. Ended up getting throttle body replaced due to a wire short in sensor. The code checked for x voltage over several sensors and threw it into limp...
  2. Is your speedo cable driven? Is that cable still...

    Is your speedo cable driven? Is that cable still attached to the transmission?
  3. Replies
    3
    Views
    676

    I don't believe (but I could be wrong) the 700r4...

    I don't believe (but I could be wrong) the 700r4 was computer controlled, 4l60E on the other hand is. Do you have a donor truck to get the parts out of?
  4. Replies
    3
    Views
    2,122

    Are you converting a 2wd to 4wd? If thats the...

    Are you converting a 2wd to 4wd? If thats the case by the time you get the axle, crossmember, trans, transfer case blah blah blah you could probably just have bought a 4wd truck. Or am completely...
  5. Replies
    3
    Views
    520

    I've never seen a shock that just had the rubber...

    I've never seen a shock that just had the rubber bushing and no bolt sleeve, they were definitely removed.

    ntbush, right on top of the gearbox, 5/8 locknut with a 3/16 allen in the middle. Check...
  6. Replies
    3
    Views
    520

    Can't catch a break.

    Like many of you I have a laundry list of things that need some attention on my truck, but can't a guy just catch a break??? When I replaced my front shocks I was pleasantly surprised (:grrrrrr:) to...
  7. Thread: Rough Country

    by Scott77
    Replies
    1
    Views
    577

    Use a Magnet.

    Use a Magnet.
  8. Replies
    14
    Views
    23,798

    I actually had to get back in there recently to...

    I actually had to get back in there recently to reseat the pump gasket. I was getting a lot of raw fumes and finally realized the gasket had pinched out a little bit on installation, of course it was...
  9. Are you sure ALL bolts have been removed? If it's...

    Are you sure ALL bolts have been removed? If it's an issue of corrsion, do you have room to swing a mallet at it? If all else fails pull the whole assembly out and pull it apart afterwards.
  10. Replies
    7
    Views
    10,014

    It is not an e-clip. Dorman "help!" products...

    It is not an e-clip. Dorman "help!" products sells a packge of retaining clips specific to the application. There's a link above to the part#.
  11. I provide custom wheelchairs for people with...

    I provide custom wheelchairs for people with severe disabilities, brain and spinal injuries, and progressive diseases.
  12. Replies
    8
    Views
    896

    Always start simple, check bulbs and fuses. I...

    Always start simple, check bulbs and fuses. I found that the retaining clip for my switch was missing, got a pack of them from Dorman, all better.
  13. Replies
    14
    Views
    23,798

    Thanks everyone, glad I could help out.

    Thanks everyone, glad I could help out.
  14. I was able to ballpark the location of the pump...

    I was able to ballpark the location of the pump by poking my head into the wheelwell, but when I cut the carpet back it was quite obvious where I needed to cut. Iwas thinking about several other ways...
  15. Cutting an access panel to replace fuel pump.

    Hey everyone, I did some searching and wasn't able to find any good info on cutting this panel. I decided to do a little write up, hope it can help someone. First I will give a little explaination as...
  16. Replies
    14
    Views
    23,798

    Cutting an access panel to replace fuel pump.

    Hey everyone, I did some searching and wasn't able to find any good info on cutting this panel. I decided to do a little write up, hope it can help someone. First I will give a little explaination as...
  17. It's the new one that came with the pump, I'll...

    It's the new one that came with the pump, I'll try some lube as recomended, thanks.
  18. Getting the fuel pump gasket to stay where it belongs?

    Hey all, I'm in the process of changing out the fuel pump on my 97 Tahoe 5.7l 4 door. I can't seem to get the gasket to stay seated, once I tap the lock ring into place part of the gasket is sticking...
  19. Thread: Exhaust Help

    by Scott77
    Replies
    9
    Views
    1,361

    Eliminating the backpressure does not hurt...

    Eliminating the backpressure does not hurt performance. Using such a large diameter pipe that you eliminate velocity is what hurts performance. A single 3 inch is more than enough for a stock or mild...
  20. Replies
    7
    Views
    1,002

    You generally can't tell if a soft line has...

    You generally can't tell if a soft line has collapsed by looking at it.
  21. Replies
    4
    Views
    1,940

    Can you extract whats left? You can most likely...

    Can you extract whats left? You can most likely get a replacement bleeder screw. Cheaper then replacing the caliper and easier then drilling and tapping (which would create a larger threaded hole...
  22. Replies
    7
    Views
    10,014

    Just for the record, I finally ordered the clips,...

    Just for the record, I finally ordered the clips, and my brake lights work just fine now. Thanks.
  23. Replies
    7
    Views
    10,014

    Thanks a lot

    Thanks a lot
  24. Replies
    7
    Views
    10,014

    https://www.dormanproducts.com/cgi-bin/vm91corp30r...

    https://www.dormanproducts.com/cgi-bin/vm91corp30r/item-dtl.w?sid=ankadirbcikUaacd010135191795199899&item=13808&icrid=&clt=hwrap1&vsrch_str=13808&vsrch_brand=ALL&vsrch_cat=ALL&st_amount=&end_amount=&s...
  25. Replies
    7
    Views
    10,014

    Brake light switch issue. 97 Tahoe

    My brake lights were not working, hazards and everything else were fine. I finally traced it back to the brake light switch, which I replaced. Shortly thereafter they stopped working again. After...
Results 1 to 25 of 34
Page 1 of 2 1 2