GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: FergusonT

Page 1 of 16 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    2
    Views
    580

    haven't looked at a carfax for this truck, but I...

    haven't looked at a carfax for this truck, but I bet it was in an accident. If you look close enough you can tell some of the body panels are not exactly lined up right on the passenger side. It...
  2. Replies
    2
    Views
    580

    '99 Silverado Window Noise?

    So I noticed the day I got this truck, last year on easter weekend, that it had some wind noise coming from the passengers side door/window. In colder temperatures the noise gets louder.

    If I am...
  3. Replies
    23
    Views
    3,517

    So far in the past few months this truck has had...

    So far in the past few months this truck has had the fuel pump/filter, plugs/wires, intake gaskets, alternator, ignition switch, ignition lock cylinder housing, fuel pressure regulator,...
  4. Replies
    23
    Views
    3,517

    Your probably right.

    Your probably right.
  5. Replies
    23
    Views
    3,517

    Yeah, a very poorly installed remote start wiring...

    Yeah, a very poorly installed remote start wiring job. When I was under there looking for the flasher relay I noticed everything was a cluster mess. Nothing was mounted where it was supposed to be,...
  6. Replies
    23
    Views
    3,517

    Just got it back today. Replaced lock cylinder...

    Just got it back today. Replaced lock cylinder housing and soldered some wires into the ignition switch.
  7. Replies
    23
    Views
    3,517

    Thanks for the words of encouragement there J...

    Thanks for the words of encouragement there J lol. Well they have done right with my families stuff, and I haven't actually taken a vehicle to a shop in years, this is one of the reasons why.
  8. Replies
    23
    Views
    3,517

    He called today, said he needed to replace the...

    He called today, said he needed to replace the ignition switch....Then later he says something about the ignition lock cylinder housing.

    - - - Updated - - -

    At this point I have so much other...
  9. Replies
    23
    Views
    3,517

    I think the guy at the shop actually did that. ...

    I think the guy at the shop actually did that. He said he has some experience with the passlock on these. He said he installed some remote starts on some of these GM vehicles with the passlock, but...
  10. Replies
    23
    Views
    3,517

    Seems like a simple concept to me.

    Seems like a simple concept to me.
  11. Replies
    23
    Views
    3,517

    The key doesn't have an external chip. It will...

    The key doesn't have an external chip. It will start for a split second, literally like one revolution and then it shuts off. Its at a shop now, the guy is looking into something in the ignition...
  12. Replies
    23
    Views
    3,517

    Well I no longer have the remote start, I had the...

    Well I no longer have the remote start, I had the guy at the shop completely remove it and wire everything back to factory spec.
  13. Replies
    23
    Views
    3,517

    http://www.ebay.com/itm/Fortin-PASSLOCK-SL2-V2-GM-...

    http://www.ebay.com/itm/Fortin-PASSLOCK-SL2-V2-GM-Passlock-Passkey-VATS-Transponder-Key-Bypass-Module-/160974636448?pt=LH_DefaultDomain_0&hash=item257ad605a0


    This good?
  14. Replies
    23
    Views
    3,517

    Ok...that is actually a great diagram of some of...

    Ok...that is actually a great diagram of some of the solutions I was reading. Thanks J.
  15. Replies
    23
    Views
    3,517

    '99 Silverado Passlock solution?

    So I find out my truck has a remote start system wired in, had no idea until now. Bought the truck last year on easter weekend. The previous owners didn't give us any remote or anything

    So I...
  16. Replies
    0
    Views
    332

    1999 Silverado 5.3 Leaky Injector?

    So I have a no start issue. It starts for a split second then it just continues to turn over. It will run long enough to burn off some starting fluid so I know I'm getting spark.

    One thing I...
  17. Replies
    27
    Views
    3,085

    So looking at the bolts and the way the manifold...

    So looking at the bolts and the way the manifold gaskets have rubber that goes around the bolt holes, I am assuming that the bolts and the sleeves on the bolts are designed to seal the manifold when...
  18. Replies
    27
    Views
    3,085

    Warranty the gaskets out? I pulled them off and...

    Warranty the gaskets out? I pulled them off and see nothing wrong with them.

    - - - Updated - - -

    Unless I am missing something, which is likely given my track record on this project...I got a...
  19. Replies
    27
    Views
    3,085

    Haynes was right, I just didnt realize it was...

    Haynes was right, I just didnt realize it was Inch/lbs. I was right around 40lbs....it did crush one of the rubber grommets on one of the bolts, as well as broke another.

    - - - Updated - - -
    ...
  20. Replies
    27
    Views
    3,085

    I've got the specs and the sequence from a haynes...

    I've got the specs and the sequence from a haynes manual, the problem was I was using a bad torque wrench. I was using my dads old wrench, he goes "oooh yeah, I used that on my '67 Camaro back in...
  21. Replies
    27
    Views
    3,085

    re installing, I got it out though. It snapped...

    re installing, I got it out though. It snapped up high thank god. Just spent all day running around and calling places, can't find anywhere. Wandered around a junk yard for about 45 minutes, no gm...
  22. Replies
    27
    Views
    3,085

    Well well....Last night....snapped a manifold...

    Well well....Last night....snapped a manifold bolt..........
  23. Replies
    27
    Views
    3,085

    You could have left it on but like i said but no...

    You could have left it on but like i said but no matter. If you have a 3/8 or 1/4 torque wrench use it because if you dont tighten the intake right it will warp.[/QUOTE]


    Yeah I saw your post...
  24. Replies
    27
    Views
    3,085

    Alright got the manifold off, peaked into the...

    Alright got the manifold off, peaked into the port for cylinder 8....and there sits the little rubber piece from my MAP sensor, sitting on top of the closed valve.
  25. Replies
    27
    Views
    3,085

    This is the gasket set I got. ...

    This is the gasket set I got.

    http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_intake-manifold-gasket-set-felpro_15781026-p?searchTerm=intake+gasket

    - - - Updated - - -
    ...
Results 1 to 25 of 398
Page 1 of 16 1 2 3 4