GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: shibby2oo8

Page 1 of 9 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    10
    Views
    1,958

    You will need a hot torch but the best way we...

    You will need a hot torch but the best way we found in the shop was to torch all the heads off then heat the cylinder head right at the stud and use stud grippers (sockects with rollers inside) to...
  2. Bout time we got a raptor counterpart. Could you...

    Bout time we got a raptor counterpart. Could you imagine a 700hp factory backed truck? "Yes i would like the 700 hp package with the 100000mi warranty..."
  3. Yea "popping" sounds like a steering shaft issue.

    Yea "popping" sounds like a steering shaft issue.
  4. Replies
    3
    Views
    639

    Go to nelsontune . Com they sell relay kits and...

    Go to nelsontune . Com they sell relay kits and harnesses. I think they have a writeup on there somewhere.
  5. Replies
    9
    Views
    1,103

    I have had my HIDs for 5 years in stock housings...

    I have had my HIDs for 5 years in stock housings with no problems. If you buy a quality light kit and use a relay to protect the factory electrics it should be good.
  6. Replies
    7
    Views
    977

    Pull the cylinder out and look for a broken tab...

    Pull the cylinder out and look for a broken tab or switch.
  7. Replies
    5
    Views
    1,109

    Change the knock sensor first, that will change...

    Change the knock sensor first, that will change the fuel tables and spark timing and help you out. Also check out the fuel pressure.
  8. Replies
    10
    Views
    1,888

    If you dont like the shift points get a tune....

    If you dont like the shift points get a tune. Right now fuel econ is the main thing so that trans will keep the engine at low rpms as long as it can.
  9. Replies
    5
    Views
    600

    Pre 96 is OBD1 and the connectors and programs...

    Pre 96 is OBD1 and the connectors and programs change between manufacturers, OBDII is 96 and later and can be scanned with the same scanner. Now cheap scanners may only do powertrain and not ABS or...
  10. Rockauto has ac delco for $125 for steel...

    Rockauto has ac delco for $125 for steel impeller, im just saving up til i can afford all the hoses. Going to be about $200 for the quality stuff. Still have not made up my mind on which brand to use...
  11. Yea im due for a pump right now on my 01, i plan...

    Yea im due for a pump right now on my 01, i plan on doing the hoses while im there.
  12. 2wd are much easier as the cv is not in the way....

    2wd are much easier as the cv is not in the way. To add to what i said before get a 6 point socket and hammer it on to thr bolt because if you round that head you are boned. If it is 4wd i recomend...
  13. I live in northern ohio and have done quite a...

    I live in northern ohio and have done quite a few. Trick is to use an air hammer and "spin" the hub on the knuckle by hitting the 3 sides until it loosens up. Byfar the easiest way. Also check the...
  14. Replies
    6
    Views
    1,150

    The shift solenoids for the 4l60e are cheap last...

    The shift solenoids for the 4l60e are cheap last time i did one and easy to do. Drop the pan and both are mounted on the VB in the rear. What i would do is ohm out the trans harness and if it checks...
  15. My 01 is the LT back when it was top dog and...

    My 01 is the LT back when it was top dog and loaded it was $33k brand new. Of course now you have a tablet mounted in the dash and sensors for sensors. When i was in school they said the mid 90's...
  16. Replies
    3
    Views
    975

    The planetary gearset or sun shell is prob...

    The planetary gearset or sun shell is prob cracked. You do need a trans unforunatly. Your better bet is to find someone to build yours if you plan on keeping it as this is a common fail. You can swap...
  17. Replies
    18
    Views
    3,215

    I allways fill them til they drip out, never had...

    I allways fill them til they drip out, never had a prob. Also rear ends get pretty toasty and the vent tube is important. Ever notice a salt truck covered in slush but the pumpkin is bone dry?
  18. Replies
    7
    Views
    1,005

    Get on their case about changing to a plated yoke...

    Get on their case about changing to a plated yoke bc they will tell you just to change the tcase fluid. So change the fluid then get the truck dirty so it doesnt look like it was just changed but has...
  19. Replies
    3
    Views
    683

    On some boosters that rod threads in/out to...

    On some boosters that rod threads in/out to adjust but you would have to check your old one
  20. Replies
    7
    Views
    983

    Pack a inline spark tester and a small straight...

    Pack a inline spark tester and a small straight pick in the truck. Next time it stalls cycle the key and see if there is fuel at the test port on the intake, then pop the spark tester on and tell us...
  21. The ball needs to pivot inside so i dont think it...

    The ball needs to pivot inside so i dont think it will last very long.
  22. Replies
    8
    Views
    1,525

    Meh, ive done them all with silicone and have had...

    Meh, ive done them all with silicone and have had no issues.
  23. Replies
    10
    Views
    1,439

    Craigslist, i have bought 2 sets at a steal off...

    Craigslist, i have bought 2 sets at a steal off craigslist but you have to be patient.
  24. Thread: Clunk sound

    by shibby2oo8
    Replies
    9
    Views
    1,037

    I would think so, the plating allows it to move...

    I would think so, the plating allows it to move easier so it shouldnt matter if its going into a tail housing of a transmission or a transfer case.
  25. Thread: Clunk sound

    by shibby2oo8
    Replies
    9
    Views
    1,037

    You need a nickel plated slip yoke, put one on...

    You need a nickel plated slip yoke, put one on mine almost 4 yrs ago and not probs since.
Results 1 to 25 of 225
Page 1 of 9 1 2 3 4