GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: 2COR517

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    4
    Views
    757

    Year/model?

    Year/model?
  2. Replies
    10
    Views
    2,867

    Any pics of these melted electrodes?

    Any pics of these melted electrodes?
  3. Replies
    10
    Views
    2,867

    AC Delco CR43TS, gapped at .035.

    AC Delco CR43TS, gapped at .035.
  4. Replies
    4
    Views
    5,971

    It's a pretty good sized job. It's coming out...

    It's a pretty good sized job. It's coming out from inside the cab. You have to let the steering column down, and pull the dash back. Start by removing the passenger seat so you have some room to...
  5. Replies
    5
    Views
    1,466

    Great success!!

    Great success!!
  6. Replies
    5
    Views
    1,466

    If you have the welding equipment handy, that...

    If you have the welding equipment handy, that would be the ticket. The rapid intense heat will break the corrosion between the bolt and knuckle too. Once you get the nut welded on, the bolt should...
  7. Replies
    8
    Views
    1,197

    The drain tube is located near where the heater...

    The drain tube is located near where the heater hoses go through the firewall. Just a little pop-in rubber elbow.
  8. Forget about the TBS, CAI, and chip. Get a...

    Forget about the TBS, CAI, and chip. Get a custom tune instead.
  9. Replies
    4
    Views
    849

    You never lined it up after the lift kit?

    You never lined it up after the lift kit?
  10. Replies
    3
    Views
    752

    Sounds like the master cylinder is leaking...

    Sounds like the master cylinder is leaking internally
  11. Replies
    3
    Views
    860

    Some of the 5.3s had issues with poor head...

    Some of the 5.3s had issues with poor head castings causing coolant loss. Unless it's finally fully bled from the waterpump service.
  12. Replies
    11
    Views
    1,036

    I'd be lost without my air tools. Mostly cheapie...

    I'd be lost without my air tools. Mostly cheapie stuff, just work on my own trucks. A decent 1/2 impact is a must, as many foot pounds as you can afford. Use my die grinders the most, especially...
  13. On the Vortec 350 it's located under the intake...

    On the Vortec 350 it's located under the intake plenum. Couple hour job for the first timer. The FPR will run you about $50. Do some careful shopping you can source the entire "spider" assembly...
  14. I wouldn't replace the O2 sensor till the truck...

    I wouldn't replace the O2 sensor till the truck is starting properly. You have classic symptoms of a bad fuel pressure regulator.
  15. Replies
    16
    Views
    4,425

    Still sounds like the cooling system is clogged...

    Still sounds like the cooling system is clogged up limiting flow to the heater core.
  16. Replies
    9
    Views
    1,109

    You need more than a code reader to accurately...

    You need more than a code reader to accurately fix this. Take it to a shop with a high end scan tool. They can drive the truck and watch all the speed sensors at once.
  17. Replies
    6
    Views
    3,014

    Those codes and your driving symptoms are classic...

    Those codes and your driving symptoms are classic for low fuel pressure. Get a gauge and test it.
  18. First step is to find out exactly how hot the...

    First step is to find out exactly how hot the engine is getting. A scan tool will tell you, but they are a little more difficult to put your hands on for OBD I. A $30 infrared thermometer will tell...
  19. Replies
    28
    Views
    4,018

    Both lol. The newest packaging labels them as...

    Both lol. The newest packaging labels them as Iridium. Either way, it's the best plug for your truck.
  20. Replies
    12
    Views
    3,380

    Does a fifty watt incandescent put out the same...

    Does a fifty watt incandescent put out the same lumens as a halogen? Or flourescent? Or Mercury Vapor? Or LEDs?
  21. Replies
    9
    Views
    2,106

    Looks good to me. Just curious, did you use a...

    Looks good to me. Just curious, did you use a setup bearing for the inner pinion?
  22. Replies
    9
    Views
    2,106

    You need MORE shim under the inner pinion...

    You need MORE shim under the inner pinion bearing. That will push it towards the center of the ring gear.
  23. Thread: code p0420

    by 2COR517
    Replies
    9
    Views
    3,469

    Time for a fuel pump

    Time for a fuel pump
  24. Thread: code p0420

    by 2COR517
    Replies
    9
    Views
    3,469

    P0171 and P0174 mean that both banks are too...

    P0171 and P0174 mean that both banks are too lean. They are not MAF codes.

    What is your fuel pressure? Sounds like it's time for a new pump.

    P0420 is a non functioning cat. Get the truck...
  25. Replies
    9
    Views
    2,106

    Looks like the pinion isn't quite deep enough. ...

    Looks like the pinion isn't quite deep enough. What's your backlash spec? .015" sounds like a lot.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4