GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: Pedro

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    878

    My local dealer doesn't have any 6.0Ls listed so...

    My local dealer doesn't have any 6.0Ls listed so I can't make a good comparison, but a truck like your 1500 is worth $55,000 (what did you pay for yours if you don't mind me asking??). Actually your...
  2. Replies
    5
    Views
    878

    Buying pre-owned gas or diesel

    I've been shopping around for a pre-owned truck 2008 and up, and I've got myself in a dilemma. Looking at gas half-tons with 40k to 100k (km), price seems to be anywhere from $25,000 - $35,000 give...
  3. In all due respect to the above post, I believe a...

    In all due respect to the above post, I believe a mild cam could be justified in your application. Something like a 214 int 224 exh would give you good low end and mid range torque, and a noticable...
  4. A common misconception with the 700r4 is that the...

    A common misconception with the 700r4 is that the overdrive gear ratio is higher, thus giving you better fuel economy. This is not true. The overdrive gear in the 700r4 is actually the same (or very...
  5. Thread: tranny question

    by Pedro
    Replies
    1
    Views
    571

    tranny question

    I'm doing a tranny swap in my 81 K10 and I'm looking at a 700r4 out of a 1990 k5 blazer. I'm just wondering if that tranny would need a computer to shift properly. I believe the electronically...
  6. Replies
    0
    Views
    887

    chevy double hump head accessory holes

    I have to install A/C on my truck and I only have one accessory hole per head. Should I build some wacko bracketry and use the single hole or just have holes drilled and threaded? There is no planed...
  7. Thread: Steering arm

    by Pedro
    Replies
    1
    Views
    587

    Steering arm

    On my 85 4x4 pickup, the tapered hole in the steering arm is gouged out (this is the arm that is bolted to the knuckle with three bolts and is attached to the drag links tie rod). I have been heating...
  8. Replies
    2
    Views
    665

    I can't hear any leaks, but I must have one...

    I can't hear any leaks, but I must have one because I have to rev the motor to around 2000 to make any of the vents move. Are you talking about the black box that houses the heater core or the one in...
  9. Replies
    2
    Views
    665

    Vacuum hoses to air distributor

    So, I'm having issues with the duct work in my 85 chev half ton. When I change the settings on my duct controls (defrost to vent, vent to floor etc.), nothing happens. It has something to do with the...
  10. Replies
    2
    Views
    2,136

    Hard to tell, I have an oil leak at the back of...

    Hard to tell, I have an oil leak at the back of the motor that saturates the slave cylinder and the line. I'm gonna run outside and check it out.
  11. Replies
    2
    Views
    2,136

    Air in hydraulic clutch system

    I replaced the clutch in my GMC 3/4 ton 4x4, and ever since the hydraulic system has been poor. I've tried three different methods to bleed it, each with no luck. It will work for a few days, and...
  12. Replies
    5
    Views
    1,028

    Losers. A bunch of punks flipped my buddy's car...

    Losers. A bunch of punks flipped my buddy's car into the ditch a few months ago. Within a minute of the news spreading we had three trucks flying down the gravel roads after the guys, unfortunately...
  13. I think they will rub, buddy. The wider the tire,...

    I think they will rub, buddy. The wider the tire, and with a spacer, you're going to have more area that will have to clear your fender/mud flap when you turn. The outer edge of your tire is what...
  14. Thread: Idle Trouble

    by Pedro
    Replies
    2
    Views
    806

    Idle Trouble

    I recently rebuilt a 350 engine that I stroked because I had a 400 crank available, but that's besides the point. The motor's got about 1000 miles on it since the rebuild and it ran strong with no...
  15. Replies
    9
    Views
    2,359

    I completely agree with 2COR517. Making a 2wd...

    I completely agree with 2COR517. Making a 2wd truck into a 4wd truck is a major project. You may find it not to be worth it in the long run. A project like that would probably not be the most cost or...
Results 1 to 15 of 15