GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER

Search:

Type: Posts; User: 85 S10 Man

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    1,226

    yeah i had my alternator tested and now it's bad...

    yeah i had my alternator tested and now it's bad so that's a other 130.00 bucks going in to it LOL.But that's with a life time warranty on it oo. so if it ever goes out then i can take it back and...
  2. Replies
    7
    Views
    1,226

    yeah me too i'm glad to get my little gas saver...

    yeah me too i'm glad to get my little gas saver back on the road again. but when they told me the price of the distributor i liked to had a heart attack LOL
  3. Replies
    3
    Views
    1,208

    universal cooling fan Question

    i have a 1985 chevy S10 with a 2.5L 4 cylinder in it.Well i changed the engine out to a 1989 2.5L 4 cylinder with wiring harness and everything.

    the problem i got is the clutch fans are...
  4. Replies
    7
    Views
    1,226

    Yeah i found the problem today i just put a new...

    Yeah i found the problem today i just put a new 140.00 distributor in it and it started right up. i thought that was what i it was but i figured i would ask here and see if anyone knew anything about...
  5. Replies
    7
    Views
    1,226

    Ok just replaced the coil and still nothing....

    Ok just replaced the coil and still nothing. check every fuse in the truck and everything i'm about to shred this dang thing.

    So i will ask again does anyone have any thing they can think of so i...
  6. Replies
    7
    Views
    1,226

    1984 chevy S10 no fire to plugs

    i done a engine swap to a 1989 S10 2.5L engine about a week and half ago and it ran good after retiming and everything. I used my timing light to confirm that it's right on what the book says. Well i...
  7. Replies
    1
    Views
    1,577

    Never mind i found one and bought it thanks...

    Never mind i found one and bought it thanks everyone
  8. Replies
    1
    Views
    1,577

    Looking for a 2.5 Chevy S10 Engine

    I'm looking for a other 2.5 Chevy S10 Engine for my 1985 S10. I had one but the guy told me it was rebuilt less then 1500 miles before it was pulled well i think he told me a load a crap. because...
  9. Thread: s-10 pickup

    by 85 S10 Man
    Replies
    2
    Views
    1,037

    Wanted to Buy What's your location? i have one here that a 1985...

    What's your location? i have one here that a 1985 with good trans and everything but the engine is blowed up again
  10. Replies
    2,389
    Views
    183,056

    Well i didn't do it this time but i'm having to...

    Well i didn't do it this time but i'm having to look for a other engine. But that's ok i got a 350 Four bolt main to in to it now.
  11. does anyone know anything about this...

    does anyone know anything about this stuff?????????
  12. oh i c well the crack i have is in the water...

    oh i c well the crack i have is in the water jacket under the 3 freeze out plugs. its just got a few pin holes but i been told this will fix it and it will never leak no more.but i really don't know...
  13. Liquid Glass Metallic Seal-Up How good is it on cracked blocks

    i got a block that i welded up but it still has some little pin holes in it. and i tried to weld it again with no success of fixing the holes in it. well to make a long story short i had a mechanic...
  14. Replies
    9
    Views
    1,353

    hey i bought it back and i am wondering how much...

    hey i bought it back and i am wondering how much nickel do i need in a welding electrode rod do i need to weld cast iron?

    I can get some rods with 55% nickel but i don't know if that will be...
  15. Replies
    8
    Views
    1,669

    well every junk yard i called or went to they...

    well every junk yard i called or went to they don't have one. and Trust me i been to pretty close to 150 junk yards in Tennessee and still haven't found one yet. and when i do find one it was either...
  16. oh i c well i'll write this down and remember it...

    oh i c well i'll write this down and remember it next time in case i get a other block that is cracked.
  17. yes that was the first thing i did. and it just...

    yes that was the first thing i did. and it just didn't hold like i thought it would so i got rid of it.
  18. yeah i was using the gas with the stainless wire...

    yeah i was using the gas with the stainless wire but it still didn't hold worth a nothing. so i got rid of it to other guy that needed a few parts to get his engine going.
  19. yeah i got rid of that engine and working on a...

    yeah i got rid of that engine and working on a other one. i'm putting main bearings and new gaskets on it when i get the block back for the shop after having it checked out good.
  20. Replies
    8
    Views
    1,669

    Here is some pictures of the crack in the number...

    Here is some pictures of the crack in the number cylinder. it's just a hair line crack but it's got me puzzled how it got there. i cleaned it best i could with a wire brush on a drill.

    43119...
  21. Replies
    8
    Views
    1,669

    yeah i been searching the internet and haven't...

    yeah i been searching the internet and haven't found a shop yet to do it. But I'll keep searching and i might find one if not I'll go to pull a part and pull the best looking block out of a junker.
  22. Replies
    8
    Views
    1,669

    it's just a hair line crack about middle way's in...

    it's just a hair line crack about middle way's in the number 1 cylinder. and I'm worried that is where the water is getting in to my oil at but i'm not sure unless i can find someone to test and see...
  23. Replies
    8
    Views
    1,669

    Cylinder resleeving Question

    I want to know if it is possible to resleeve a cylinder on a 4 Cylinder block?

    Because my number one cylinder looks like it has a hair line crack in it but i i'm not sure yet but i'm goin to have...
  24. Replies
    9
    Views
    1,353

    Oh i c well i done sold it to a other feller that...

    Oh i c well i done sold it to a other feller that needed the head off of it. What i should have done is waited until i found out more about welding cast iron before i got rid of it.
  25. Replies
    9
    Views
    1,353

    oh i c well i'm on the hunt again for a 2.5L S10...

    oh i c well i'm on the hunt again for a 2.5L S10 engine i guess
Results 1 to 25 of 31
Page 1 of 2 1 2