Results 1 to 10 of 13
01-26-2007, 06:26 PM #1
- Join Date
- May 2006
GMC Heater Blower Motor Removal ??? 1993 Sierra
Can anyone throw me some info on removal of the blower motor rubber cover so I can get at the blower motor for its removal? It looks like a real pain to do. I cannot see how that darn cover comes off. I have 2 shop manuals but they do not show how to remove the cover/motor. I have replaced about everything else on these trucks but this.
Thanks for your help!
1997 Suburban, Discovery Conversion
FYI: I am on the 9th fuel pump for the Suburban within the past 45,000 miles, 4 in one year. Is there a support group for those like me?
01-26-2007, 09:07 PM #2
LOL yes we have a support group for fuel pumps, of course.
With that many tank drops you must be a pro. Whats your best time, I think Iíll start a thread on just pump removals.
How many other things do you brake in the process. You know simple things.
I have seen and heard off people cutting a hole in the bed just over the pump and then making a cover plate.
Technology is great, when it Works,
And one Big Pain in the Ass When it Doesnít.
Detroit Iron Rules, All the Rest are Just Toys.
94 GMC Burban, 5.7L (350), 4X4, Auto
86 GMC Burban, 350, 2 WD, Auto
79 GMC pickup plow truck, 400, Full time 4X4, Auto
86 Pontiac Fiero SE, 2.8L, Auto, only mid engine American car
See a Pattern yet?
15 year GM assembly line worker.
01-26-2007, 09:36 PM #3
It should just slide off the motor, but you'll still need to manipulate it around the tight areas up under the dash. Have you taken the dash apart yet, or were you trying to get it done without touching the dash much?
I just checked mine, and it slid off, but I wouldn't be able to remove it without babying it past the dash, or taking the passenger's side apart.Patrick
01-26-2007, 10:48 PM #4
- Join Date
- May 2006
I can pull the cover away around the edges a bit, but it feels like it is mounted to in some way.... a real pain for something that should be easy.
Please do thow some input my direction when you can. I have only high left on the fan speed setting and it is squealing like crazy as well.
On the fuel pump thing... I just put my 9th in earlier this week. Something I always have to do is change out the the spark plugs, they get fouled badly for some reason even though the engine wasn't getting gas. I still have yet to change the plugs for this last pump change, then she will fire right up.
Not until the 5th pump did I pull the carpet up cut an access hole (it took me a while to learn my lesson on this deal) I did this when I had the tank dropped of course. I am sooooo glad I did this.
I haven't broken anything in the process of doing this. I do wish the pump harness had a bit longer wires so I wouldn't have to get under the truck to disconnect. There are some very basic engineering/common sense issues that should have been corrected before any of these trucks were built... but hey, it doesn't have to make sense does it.
Last fall I helped a neighbor change his pump fairly fast on a 94 Sub. He was trouble shooting the relays, ect. I told him what the problem was, he didn't want to believe me but went with me on it and the truck fired right up on my mark when the job was done.
I have earned my stripes on this fuel pump thing. I have changed every one myself... just me, and didn't blow myself up in the process... yet. Questions on pump related issues? Try me, I "might" be able to help out.
01-26-2007, 11:48 PM #5
I'm not sure what else to say about the rubber cover for the fan motor. I can tell you that it did have resistance when I pulled on it, but it gave way fairly easy. Not like something broke, but more like it released. I looked through my book to double check, and it doesn't indicate anything about the cover, so I'm inclined to think that it snaps into place, and just takes a little tug to break free.
Maybe someone else has some input on this.
01-27-2007, 08:22 AM #6
Blower speed is controlled by a circuit board, used to be under the hood on the ac hood.
Now they are under the dash, not bad to get at, if you can stand on your head.
The older ones looked like a triangle peace of plastic with 3 screws. It had 3 or 4 coils of wire on the inside. The new one is a circuit board.
So if you still only have 1 speed when you get the new motor in, that’s your problem.
01-27-2007, 08:41 AM #7
On my 93 burb, I undid the dash on the right side by loosening the nut on the stud mounted on the A pillar. The dash comes up enough to let my big mits maneuver in the confines. Cover came off with a tug. I pulled the glovebox liner and removed the big silver computer just underneath for a little more room to work. Check my post on heater fan removal for more detail.
On the fuel pump side, my mechanic recommends keeping the fuel tank at 1/4+. He says the fuel is the coolant for the pump and they overheat when the tank is below that level.There is no way to happiness....happiness is the way.:yipi:
High Desert SoCal
93 K1500 burb (personal) 350 AT 3" Lift 250K+
02 Honda Civic LX
Looking for a 1990's Miata for an engine swap
01-27-2007, 10:27 AM #8
- Join Date
- May 2006
I hope to dig into the blower removal today. It is a bit cool out there this morning and I have a couple other projects going on in my shop right now so I think this is an outside thing today. The resistor for the speed control... is that not located on/near the blower motor? Does anyone have a location on this?
Concerning the fuel pumps.... fuel level is not an issue. Even at 1/4 of a tank the majority of the pump is not even submerged for effective cooling.
On my Sub with the 42 gal tank with it at half full, the top portion of the pump is sticking out of the gas. For 2-1/2 years+, by the time the tank is getting close to 1/2 full I am filling it again....it made no difference. In 2005 I went through 4 pumps. Of those, one lasted from Thanksgiving Day to Christmas Day, and one that was brand new from GM was bad right out of the box. I have heard all the 'fixes" and tried eveything... it doesn't matter. It is just a roll of the dice.
The pump is just a bad design that GM won't own up to. Our 97 Park Avenue has 205,000+ miles on it and has never had a pump replaced. We know many others with various GM products and have never replaced pumps.... unless they have a GM truck. I know of several people that have that are on their 5th or 6th pump... or more. As I said earlier, I just installed #9.
Overwhelmingly, the pump problem is with the trucks GM, that cannot be ignored. "If it looks like a duck, walks like a duck....."
If someone would come out with a different pump, not a rebuild on the bad design, a DIFFERENT pump that can be retro-fitted into these trucks they would make a million $$$!Bryan
1993 Sierra P/U
1997 Suburban/Discovery Conversion
1997 Buick Park Avenue
01-27-2007, 11:13 AM #9
01-27-2007, 12:00 PM #10
- Join Date
- May 2006
With the pressure that the Vortec system requires simply hooking up an electric pump with a hose isn't really a quick fix option. On the TB systems the pressure around 15psi +- is a touch more forgiving with a very minor fluctuation in psi. The Vortec system needs rock solid pressure, very touchy.
A solidly made replacement would be welcomed by many!
By Badbrad10 in forum General Chevy & GM Tech QuestionsReplies: 2Last Post: 12-15-2009, 12:45 PM
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 10-28-2009, 09:46 AM
By jkw_GMC in forum General Chevy & GM Tech QuestionsReplies: 3Last Post: 07-26-2009, 10:44 PM
By ross in forum Audio, Video & Gadget TechReplies: 4Last Post: 04-28-2009, 12:09 PM
By Zoner in forum Chevy Silverado Forum (GMC Sierra)Replies: 5Last Post: 03-22-2007, 07:40 PM