Results 1 to 10 of 10
Thread: Bent axle?
10-09-2012, 11:23 PM #1
ive been driving on this axle like this for about 3 years now, hit a curb back my freshman year in college and im wondering if its something that requires attention...
i recently am now getting a bad creak (like old door creak) from the right rear brakes when i push on the pedal while moving or stopped, while i pump the brakes it just creaks and creaks, pretty loud.
Who could point me in the right direction for a decent replacement axle? and obviously might as well replace both if necessary, doesnt it seem the left rear might be a little bent too or no?
Last edited by reggiecab2000; 10-09-2012 at 11:36 PM.2000 Chevrolet Silverado
4.3L V6, 4L60E, 2WD, Single Cab
Poweraid TB Spacer
Flowmaster 10-series exhaust (dumped)
Edge CS insight monitor
LS-1 Dual Electric fans
Corvette tranny servo swap
Head Unit: Alpine
Speakers: Alpine SPR-60C 6.5" component set, 4X6 Infinity Kappas
Subs: 2-12" Kicker CVT's
Amps: Alpine-M1000 (subs), Alpine MRX-F65 (Speakers)
305/70R16 NITTO Terra Grapplers
16" PROCOMP 7089's
2" leveling kit
3" Fabtech Spindle Lift Kit
Front/Rear-Bilstein 5100 shocks
35W HID Low Beams
RECON LED smoked roof cab lights
HELLA LED taillights and 3rd brakelight
HELLA FF-75 Aux. Reverse Lamps
RIGID dually D2, flush mount, wide beam
Hawk HPS Brake pads
Russell braided steel brake lines
Powerstop-red powdercoated brake calipers
Powerslot Cryo brake rotors
EGR in-channel window visors
10-10-2012, 03:47 PM #2
Is this the same rim with which the curb was hit? I do not know what the runnout spec is for the rear axle flange but I would remove the tire and check it with a dial gauge to see where it is and go from there. It was hard for me to pick out much woble from the video.2000 GMC YUKON SLT, 5.3L tow pkg, G80 rear/w 3.73 gear
10-10-2012, 04:04 PM #3
Looks like a bent wheel to me.Ray
'09 Avalanche LTZ - Black
'05 Envoy XL (sold)
10-11-2012, 11:35 AM #4
yes its the right rear wheel, the one that hit the curb.
and its not the wheel because the wheel i bent was one of my 20's, i got these new wheels and tires back in october last year and havent hurt them since
10-11-2012, 03:23 PM #5
do you know if your hub is bent? But then again the end of your axle might actually be bent.just by a little. But id check your hub first.1994 GMC Yukon, 2 door, Victory Red
Garage Link: http://www.gmtruckclub.com/forum/sho...1994-GMC-Yukon
10-11-2012, 07:49 PM #6
Since you can get both wheels in the air, I would swap wheels from side to side and be sure the woble stayed on the right side. If so, then I would have to go with your assesment and call it a bent axle.
10-13-2012, 08:08 PM #7
10-14-2012, 09:49 AM #8
OK, the axle is bent and no question about that. Tire wear? Oh yes. If you can see the woble then it is absolutely to much and bad. Replace the one and inspect the other and replace it if it worn or damaged. The cost of gaskets and oil for the differential could go along way in off setting the cost of replacement of the left axle if done at a later time.
10-14-2012, 10:40 AM #9
the dealer part number for my axle is 12471369 dealer wants $552.00 each! yeah right ive found them online for between 100-200 from dorman, alloy usa, motive gear, etc. Now being i dont think i need any super ultimate high strength axle, which brand would yall recommend? i am running 305/70R16 tires(33X12.5) 10 ply tires. what is reliable?
10-15-2012, 05:26 AM #10
Buy the one made in the USA! If it exists.
By parts bot in forum Chevy Parts eBayReplies: 0Last Post: 09-23-2012, 10:30 PM
By dtricks in forum Chevy Silverado Forum (GMC Sierra)Replies: 3Last Post: 09-05-2012, 12:17 AM
By 98regcab in forum General Chevy & GM Tech QuestionsReplies: 3Last Post: 01-02-2011, 10:42 PM
By BrokeEnthusiast in forum Lifted & Offroad SuspensionReplies: 7Last Post: 12-26-2009, 12:33 PM
By 05Colorado in forum Chevy Colorado Forum (GMC Canyon)Replies: 11Last Post: 11-08-2009, 09:30 PM
Tags for this Thread