Results 1 to 5 of 5
11-12-2012, 08:02 PM #1
- Join Date
- Nov 2010
need help troubleshooting code P0171, P0174
I have been getting the check engine light on here lately. been getting code P0174 a few times last week, and today I got P0171 and P0174 which translates to system too lean bank 1 and 2.
The engine runs a bit rough at idle sometimes, but other than that runs just fine.
I was wondering if anyone can help me troubleshoot this and get it taken care of before bad things happen.
I have an 03 Silverado 1500 LS 2WD with 4.8 L
11-13-2012, 01:38 PM #2
Jon, more often than Not, its the 02 Sensor's being problem, and I would also Check for Vacuum Leak, after that check out the below list of other items, that could Trigger those Codes,
A Code P0171.....may mean that one or more of the following has happened:
- The MAF (Mass Air Flow) Sensor is dirty or faulty
Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF Sensors Leak the silicone potting material used to protect the circuitry.
- There could be a Vacuum Leak Downstream of the MAF Sensor
- Possible Cracked Vacuum or PCV line/connection
- Faulty or Stuck Open PCV Valve
- Failed or Faulty Oxygen Sensor (bank 1, sensor 1)
- Sticking/Plugged or Failed Fuel Injector
- Low Fuel Pressure (possible plugged/dirty fuel filter!)
- Exhaust Leak between Engine and first Oxygen Sensor
A lot of Times, Cleaning the MAF Sensor and Finding/Fixing Vacuum Leaks fixes the Problem. If you're on a Tight Budget, Start there, but that may not be the fix for certain.
Other Possible Solutions Include:
- Clean the MAF sensor. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF Sensor, and make sure it's dry before reinstalling
- Inspect all vacuum and PCV hoses, replace/repair as required
- Inspect all hoses and connections in the air intake system
- Inspect and/or test the intake manifold gaskets for leakage
- Check for a dirty fuel filter and proper fuel pressure
- Ideally you'll want to monitor short and long term fuel trims using an advanced scan tool
- If you have access, you may want to run a smoke test
A Code P0174.......may mean that one or more of the following has happened:
- The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
- There could be a vacuum leak downstream of the MAF sensor.
Possible Solutions Include:
- In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful Not To Damage the MAF Sensor, and make sure it's dry before reinstalling
- Inspect all vacuum and PCV Hoses, replace if necessary
- Check for a Dirty Fuel Filter and Proper Fuel Pressure
5.3 l 3.73 l G80
BLACK BEAR CUSTOM TUNE
SNUGTOP l COLORMATCH l KATZKIN
12-14-2012, 12:21 AM #3
- Join Date
- Dec 2012
- Southern Socal, Lol
Hey mike man you in luck. 03 surburban w 170,K+ miles. Mine did the same thing the other day and last month. I replaced my uni gas cap with new one from dlrship. Still happening. Autozone friend onbase hook up scaner to truck and P0171 & P0174 came on. Try out these links I got off of you tube first. All you will pay is for can of MAF cleaner and go from there brother. Good Luck, I will be doing it here once rain has stop.
01-15-2013, 07:12 PM #4
- Join Date
- Nov 2010
I'm still having the same codes P0171 and P0174 coming on, but just the other morning, I started up the truck and it wasnt idling right and then check engine light was flashing. I turned it off and checked the codes, and got the same P0171 and P0174, in addition I got the codes P0101 and P0300. I cleared the codes and they havent come back on yet. but still getting the 171, and 174 codes. my truck is 03 silverado 1500 4.8L with around 165K miles. the truck runs great at all speeds except at the stop lights, just idles between 500 and 1000 rpm.
I gonna try cleaning the mass airflow sensor and see if that helps.
01-16-2013, 10:38 PM #5
The intake is either warped or the intake gaskets are bad. Not a big deal, the plastic intakes on cars now tend to twist/warp after many heat cycles and need to be replaced. You could get lucky with just the gaskets but a dorman intake kit is like $250 and comes with a new intake plus everything you need. See it all the time and what gives it away is rough idleing when cold. The job is pretty straight forward with basic tools, if you unbolt the throttle body and leave it on the engine you wont have to deal with the cooling sytem. One thing to be sure to do is get a 3/8 torque wrench and tighten to proper specs so you dont warp the new one.01' 1500 LT Z71 ECSB 5.3L
line-x'd front brush guard with KC Daylighters, 6000k HID lows and highs, rewired highbeams, Trans-go mild shift kit, custom stainless duals, 3500 dually OEM taillights, K&N CAI. Still have OEM fender flairs and leveling kit in boxes waiting for time.
By duffy in forum General Chevy & GM Tech QuestionsReplies: 2Last Post: 01-15-2012, 09:20 PM
By senorbob999 in forum GM PowertrainReplies: 0Last Post: 08-26-2010, 08:50 PM
By mkruluts in forum General Chevy & GM Tech QuestionsReplies: 0Last Post: 03-13-2010, 03:00 PM
By konger88 in forum GM PowertrainReplies: 8Last Post: 03-09-2010, 10:47 PM
By hblock72 in forum GM PowertrainReplies: 2Last Post: 10-27-2009, 06:29 AM
Tags for this Thread