Results 1 to 10 of 16
Thread: New rubber 265/70R17
01-04-2013, 06:51 PM #1
- Join Date
- Jan 2013
New rubber 265/70R17
The stock tires on my new(to me) 09 Silverado 4x4 pickup are 265/70R17.
Would i have any clearance issues going to a 275 or 285 mm tire.
The truck is otherwise stock, no lifts etc.
01-04-2013, 06:55 PM #2
You may have trouble with the 285s. When I had a leveling kit, my 285/70/17s came fairly close to rubbing. I'd lean more towards the 275s.
PS...I moved your thread to our tires/wheels section.
Mike (Denver, CO) - 2008 Sierra 1500 Z71 SLE 5.3L 4WD
SUSPENSION: Rancho 4" Suspension Lift; Rancho RS9000XL Shocks; Rancho Skid Plates; Rancho MyRide Wireless Shock Controller;
TIRES: BFG All Terrain KO 315/70/17
DRIVE TRAIN: 4.56 Gears; Detroit TrueTrac Differential; True Cool 40k Transmission Cooler
PERFORMANCE: DiableSport Predator Tuner; Custom Tuned by Diablew; Magnaflow Exhaust; AFE Cold Air Intake
ELECTRONICS: Kenwood DNX6180 Touchscreen; Subthump box w/10" Kicker; Driver Information Center (DIC); Rear View Camera
ACCESSORIES: Westin Brush/Grill Gaurd; Westin Nerf Bars; Truxedo Tonneau; 20% Tint; Tow Mirrors w/Heat & Signals
01-04-2013, 06:57 PM #3
- Join Date
- Jan 2013
Thanks for the advice, I have about 50% wear
and thought i would start the search.
01-04-2013, 07:00 PM #4
If possible, have the tire shop mount up the 285s and check.
When I purchased my 315/70/15s (35s), the retailer I purchased my tires from did that for me at their suggestion and we found the largest tires that would fit, which by the way were smaller than what I originally thought would fit.
Last edited by mfleetwood; 01-07-2013 at 04:05 PM. Reason: Clarified tires size
01-07-2013, 12:31 PM #5
On the older trucks if you cranked the torsion bars it would just clear 285's but on the new trucks you would need to either get a spacer block for the coil-overs or a set of the quick-lifts that are basically like loaded sturts that are taller.
mfleetwood, I love the stance of your truck. Thats what I want for my truck but unfortunately I can always either afford a lift or a set of tires, not both.01' 1500 LT Z71 ECSB 5.3L
line-x'd front brush guard with KC Daylighters, 6000k HID lows and highs, rewired highbeams, Trans-go mild shift kit, custom stainless duals, 3500 dually OEM taillights, K&N CAI. Still have OEM fender flairs and leveling kit in boxes waiting for time.
01-07-2013, 12:45 PM #6
01-07-2013, 01:20 PM #7
I have 2 separate body styles of trucks, look at my signature, and NEITHER of them need any lift to fit 285s, I have taken them off roading and never had rubbing or damage to the tire or body from suspension compression and them hitting anything either. You should be just fine going to a 285 tire. My dad has an 08 z71 and I know 285s fit on that without clearance issues or having to put in any spacers.99 K1500 Suburban LT "THE BEAST"
Hypertech III, K&N, true dual
01-07-2013, 03:58 PM #8
I noticed in your sig, you have a 285/75/16s and it's not a NNBS, which means it may not be exact match to use as an example. But, since you used your Dad's NNBS truck as an example as well (which is I think is a much better comparison to use than your vehicles), it would be helpful if you included the rim and sidewall size so the OP can compare more accurately. Again, a 285/75/17 is about 1" larger in diameter than a 285/70/17.
01-08-2013, 12:33 PM #9
I didn't mention aspect ratio(side wall) as he wasn't asking about it only the width size, all of mine are stock ratio just went to 285. My dad has factory 18s and I know others with factory 17s that went to a 285 with no issues
01-08-2013, 12:44 PM #10
^^^ I don't think he gets it00 Chevy Tahoe LT, 5.3 4x4
By parts bot in forum Chevy Parts eBayReplies: 0Last: 12-05-2012, 05:00 PM
By parts bot in forum Chevy Parts eBayReplies: 0Last: 11-14-2012, 10:10 PM
By jrsavoie in forum General ClassifiedsReplies: 0Last: 12-28-2010, 06:10 AM
By BRAINTUMORBOB in forum Lifted & Offroad SuspensionReplies: 10Last: 07-13-2010, 09:07 PM
By sickboy88 in forum Lifted & Offroad SuspensionReplies: 0Last: 07-28-2009, 04:16 PM
Tags for this Thread