Results 1 to 10 of 10
Thread: Cracked front axle boot.
01-20-2013, 08:55 AM #1
- Join Date
- Dec 2009
Cracked front axle boot.
While lubing my ol '98 Silverado I noticed (with wheel turned) one of the front axles boots has a crack. I know this will have to be fixed. I don't think I have the tools (or knowledge) to replace it. I also fear it's going to cost me mucho $$$$. Question(s) are, is there anything I can do to patch it to make it last a little longer? The axle actually looked pretty clean. On other vehicles (fwd) I have owned the boot cracks, dirt gets in and ruins bearing. Then they replace the whole shebang. Realistically, how long do I have before it fails? How much money are we talking for a fix? How many parts will be replaced?
01-20-2013, 09:07 AM #2
- Join Date
- Apr 2010
- Piermont,NY, back in Northern NJ now, But may be in IL soon....
There used to be a universel quick fix boot on the market from I think Moog. When I had my lifted S-10 Blazer I used to use them..it just goes over the old boot or the axle comes with grease and glue and clamps to keep it shut..I think they were about $25.0008 Z71 Avalanche Mods to date: K&N CAI,Hellwig Swaybars and End Links, Corsa Sport Exhaust, Superchips Programer,IPCW LOF & 3rd brake light and tails, AMI Gas door,Show Hooks and Door locks, Enkei Wheels, with Pirelli tires, StreetScene Bowties, Grant Steering wheel,Muth signal mirrors,SSBC Big Brake kit,Huskyliner Mug gards,Floor mats and Hood shield, McGard Lug nuts and locks, Bedrug, Cervini's Ram Air hood,35watt HID Fog lights, Sylvania bulbs all around ZXE's Highs and Lows, WhiteNight Back up lights,Sirius and HD Radio, SnugTop sitting on deck now Got a Softopper on now,Tempress Boat Hatches.... New Bilstein shocks are on... New Mods coming soon..... X
01-20-2013, 09:54 AM #3
- Join Date
- Dec 2011
- Blog Entries
Just make sure u get it fixed soon or you can ruin the CV joint from lube failure or contaminants Usually the replace isnt to pricey, but a damaged CV is because you have to replace the whole shaft and joints.
1996 Chevy Tahoe LT 5.7L V8 4X4 205,000+ miles. Built proudly at Janesville Assembly in Janesville, Wisconsin
Basic mods: Lights all over, bunch of electrical work, and a couple cooling mods.
Check out my other mods in My Garage: http://www.gmtruckclub.com/forum/sho...t-Tahoe-4-Door
01-20-2013, 11:25 AM #4
- Join Date
- Mar 2007
- Grand Prairie, Texas
- Blog Entries
If you use the truck for any type of off-roading the universal fix boot probably wont last very long, their a cheap quick fix and quality/longevity are reflected.
Remove and replace the CV shaft as soon as possible, quality rebuilt/re-manufactured replacement CV shafts are available for reasonable prices at most auto parts stores. And they take less than an hour to replace with normal hand tools.
There's no way to measure how long it will last before the boot totally fails and the joints begin destroying themselves (actually the joints are probably already forming corrosion and getting excessive wear from moisture and debris thats slipped in), but the end result can be a lot more expensive than a new CV, this is a job thats better to be proactive with so you dont end up with something more expensive down the road.
01-20-2013, 12:00 PM #5
to repair this is not a big job with the proper tools. also this is a common well known repair to replace the cv assy/boot.
problems that will occur if in the rust belt would be hub removal. this can be hard to do as the hub locks into the lower control arm sometimes. you will also need a manual to guide you threw the process so this is torqued and installed properly but for sure not a complex job.
if you had all the tools and an air gun about 1 hr job. with a crack this means dirt / water got in, now it is rusting and grit is wearing away at the joint unless this is a small crack.
good luck ..
01-20-2013, 12:35 PM #6
A new complete shaft is around $60. you can get them out without having to pull anything else. Just remove the bolts holding it to the front diff flange, take off the nut at the wheel hub, and sometimes you have to remove the swaybar link. You should be able to slide it right out.
1995 Silverado 4x4
6" BDS Suspension Lift-3" Body Lift-Add A Leaf in rear -Trailmaster SSV Shocks-Duel Steering Stabilizer Kit -AirAid Cold air intake-
4.56 Gears with Detroit Auburn Locker-Pro-Comp Traction Bars with duel shocks-Aluminum Skid Plate Kit-38.5" x 16.5" Mickey Thompson Baja Claws-Constant Dropping fuel gauge
2005 Yukon XL Jet Power Programmer, Bilstein Shocks, Bilstein rear springs, Helwig Anti-sway bars, EGR Window Visors, EGR Hood Shield, Denali Headlights, Headlight harness upgrade, GE NightHawk Bulbs, White Night Rear lighting system, Russell Braided SS brake lines, PowerStop Brake pads, PowerStop cross drilled and Slotted Rotors, http://www.gmtruckclub.com/forum/sho...5-GMC-Yukon-XL
2002 Silverado ext cab 2wd (Sold)
2003 Yukon XL (Totaled)
01-20-2013, 04:04 PM #7
- Join Date
- Dec 2009
Thanks everybody! I'm encouraged to try this repair myself. Anybody got a recommendation for a good manual?
01-21-2013, 07:28 AM #8
@Pikey, that price is correct. I had to replace mine this summer. Was around 70 total, but I think there was a core deposit. As for changing it, it wasn't bad, just like what he said. Remove the bolts and slide out. A buddy was helping me do my shocks and we noticed it so we replaced it then. we had already installed the front shock then noticed it had to be replaced. It was easier to take the shock off and change, then to do it with it on.-K&N Air Filter
01-21-2013, 03:10 PM #9
Everything I've ever read is that it is better to replace the axle than just the boot. Since the boot has ripped, the axle is probably original (1998), so the CV joint is pretty worn out anyway. I would not spend any money at all on a 15 year old axle. From what I've also read, a mechanic will remove the axle to replace the boot.
2013 Silverado LTZ White Diamond Crew Cab
Advent OGM1 Navigation
Husky Liners GearBox Underseat Storage
EGR Rail Caps
K&N Air Filter
Flowsound 40 Muffler
Hypertech Max Energy Tune (only top end limiter removed and AFM disabled)
Chrome Tailgate Handle Cover
TonnoPro HF-155 Tonneau Cover
WeatherTech Front and Rear Splash Guards
Husky Liners X-Act Contour Floor Liners
WeatherTech Side Window Deflectors
01-23-2013, 08:25 PM #10
For the pita and money a new axle is the way to go, i have done it 3 ways, 1 replace, 2 i put a boot that used like 6 tiny bolts and a split boot on my tempo, it held but wasnt very good as the bolts ruined flexability, 3 take apart the axle, now depending on age this is a bitc*. you have to completely remove the old boot, clean out all of the old grease, wrestle a snapring off and then try to get it all back together. For $50-80 you can replace just about any cv. These thrucks are real easy too bc the inner cv bolts on and you just undo the hubnut and tap it out. MAKE SURE TO LOCKTITE THOSE BOLTS! They will come back out or shear if you use 4wd often.01' 1500 LT Z71 ECSB 5.3L
line-x'd front brush guard with KC Daylighters, 6000k HID lows and highs, rewired highbeams, Trans-go mild shift kit, custom stainless duals, 3500 dually OEM taillights, K&N CAI. Still have OEM fender flairs and leveling kit in boxes waiting for time.
By Dieselmechanic in forum POLLing placeReplies: 0Last: 01-07-2012, 09:43 PM
By joemud in forum General Chevy & GM Tech QuestionsReplies: 1Last: 11-08-2010, 09:25 PM
By ed_00silverado in forum General Chevy & GM Tech QuestionsReplies: 1Last: 07-02-2010, 11:51 AM
By gustheiceman in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 4Last: 10-26-2009, 01:54 AM
By phoebeisis in forum General Chevy & GM Tech QuestionsReplies: 0Last: 07-11-2009, 05:12 PM
Tags for this Thread