Results 1 to 7 of 7
Thread: Wheel Hub Assembly w/ Bearings
02-25-2013, 04:58 PM #1
Wheel Hub Assembly w/ Bearings
I have searched on here, but couldn't find anything. Anyway, I am looking for a wheel hub assembly with bearings for an 07 Silverado 1500 LTZ 4x2. Does anyone have a recommendation or a part number? It seems there are a lot of choices, and the ones from GM seem to be starting in the $200 range for just one.2007 Silverado 1500 LTZ 6.0L VortecMax - Magnaflow Catback
2008 Pontiac G8 GT - LS3 430 & many more goodies
409 rwhp 402 rwtq
02-25-2013, 05:45 PM #2
I always go for timken, part they are based 10 mins away and part good history. With the china steel and assm its a crap shoot anymore.01' 1500 LT Z71 ECSB 5.3L
line-x'd front brush guard with KC Daylighters, 6000k HID lows and highs, rewired highbeams, Trans-go mild shift kit, custom stainless duals, 3500 dually OEM taillights, K&N CAI. Still have OEM fender flairs and leveling kit in boxes waiting for time.
02-25-2013, 08:27 PM #3
I used NAPA's. Mine was over 200 since its the whole assembly instead of just being able to replace the bearing and I have the 4wd.David
2004 Silverado 2500 Crew Cab 4x4, AMSOIL EA air filter, Granatelli MAF sensor, Throttle body spacer, Magnaflow exhaust (true dual to 2 in 1 out muffler), 6" ProComp lift (add a leaf and 5" superlift rear block), Bilstein shocks, 35's (Cooper Disoverer ST) and 4.10 gears, Rhino Liner, EGRUSA fender Flares and widow visors, extended stainless steel brake lines, firestone airbags w/onboard air compressor, Pioneer Avic X940BT navigation, Accel backup camera.
1960 Land Rover Series II 88
2002 Nissan Altima (My Commuter)
2013 Toyota Avalon Limited (Wife's Car)
NRA Life Member
02-26-2013, 12:33 AM #4
I found some good information on rockauto.com. I like Moog stuff, but I haven't heard of Timken, and AC Delco is so damn expensive.
02-26-2013, 01:07 PM #5
02-26-2013, 01:36 PM #6
Moog bought out national i think, i went to try out a moog for my sisters impala and it wasnt a moog box. Year in still good. Timken cone bearings ate mostly usa but the hubsight be china, im not sure but i like timken the best and its what we used in the shop.
02-26-2013, 01:58 PM #7
If you have the bucks, go with a North American (US, Can, Mexico) producer, like Timken or ACDelco. If not, buy China and take a chance. I have replaced 8 front wheel hubs on 4 NBS and NNBS silverado 1500's, and opted for the import stuff each time. All have been fine, until the last pair I did, one of them had a bad ABS sensor, and will have to be replaced at some time. AutoZone sells them all, and you can ask where they were made before you buy. Also, most of their stuff carries a lifetime warranty.
By kennyb79 in forum General Chevy & GM Tech QuestionsReplies: 2Last Post: 02-12-2013, 12:06 PM
By RyDogZ71 in forum GM PowertrainReplies: 13Last Post: 08-07-2011, 03:26 PM
By bacol14 in forum Lifted & Offroad SuspensionReplies: 6Last Post: 08-16-2010, 06:37 PM
By ag90fox in forum Lifted & Offroad SuspensionReplies: 3Last Post: 03-27-2008, 07:36 PM
By bart6180 in forum Chevy C/K Truck ForumReplies: 2Last Post: 06-29-2007, 02:45 PM