Results 1 to 5 of 5
04-23-2013, 09:44 AM #1
- Join Date
- Apr 2013
Wiring Homelink in 2002 Silverado
My truck 2002 Silverado had the drop down door for the hand held garage door opener. I got the 3 button Homelink insert from a 99 tahoe at a salavage yard. All went O.K when I went to install it except I had only the hot & ground wires in my truck overhead console. What I'm wonder is what is the simple way to wire the illumination on the new 3 button homelink panel, I just installed? I don't want to wire it to the hot 12V. I would like it to work like the factory install.
Please dont answer with a bunch of odd ball suggestions, like Ive seen done with other posted questions.. ie, I wish I had it, or "I could use two of them etc.
04-23-2013, 10:00 AM #2
Tap the +12v line from your dimmer switch, run it up the driver's side A-pillar, under the headliner, to the overhead console, and connect it to the dimmer wire on the Homelink unit. You'll need to probe with a multi-meter to find the correct wire ... and its voltage should change as you (un)dim the dial.
Also, a word to the wise ... the way it works from the factory is less than ideal. Factory Homelink is wired to an always hot +12v line, meaning someone can smash your window, activate Homelink, and up your garage door goes. A safer mechanism is for you to wire Homelink's power to a switched (IGN) +12v line so that the key has to be in the ignition for Homelink to work.
Also, a word of note -- I've added Homelink to my truck. If I was not already pulling the dimmer line (as suggested, above) to my overhead console for a different reason (some stupidly bright LED switches for which I -need- a dimmer line), I would absolutely have tied the Homelink unit's dimmer wire to the same source of power used for the Homelink unit, itself. Why? I tested with variable +12v prior to installation, and the lights just aren't that bright when fully on -- meaning dimming them is relatively moot.
I was advised that this was the case, saw it for myself, but I needed the dimmer up there for other reasons, so I tied into it just because I could. It's really not worth the trouble for just Homelink, in my opinion. It just doesn't make a substantive difference. I suggest you test with a variable voltage +12v source prior to installation and see for yourself.
04-23-2013, 12:57 PM #3
Yes, I am not a huge fan of having the Homelink be always on. I wish GM would have wired it to the ignition 12V.
2013 Silverado LTZ White Diamond Crew Cab
Advent OGM1 Navigation
Husky Liners GearBox Underseat Storage
EGR Rail Caps
K&N Air Filter
Flowsound 40 Muffler
Hypertech Max Energy Tune (only top end limiter removed and AFM disabled)
Chrome Tailgate Handle Cover
TonnoPro HF-155 Tonneau Cover
WeatherTech Front and Rear Splash Guards
Husky Liners X-Act Contour Floor Liners
WeatherTech Side Window Deflectors
04-23-2013, 04:23 PM #4
- Join Date
- Apr 2013
04-23-2013, 04:47 PM #5
You really should connect the leads up direct to the battery so that you can see how dim the lights are when fully powered. You may choose to not even bother connecting them. At full brightness it's tough to tell they are on (even when dark). (It's intended to be very sublte illumination.)
By parts bot in forum Chevy Parts eBayReplies: 0Last Post: 11-19-2012, 02:00 PM
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 09-23-2010, 02:40 AM
By kevinhenry in forum Audio, Video & Gadget TechReplies: 1Last Post: 05-03-2008, 07:59 PM
By robmik2000 in forum Audio, Video & Gadget TechReplies: 0Last Post: 01-17-2008, 12:08 PM
By MN_Burbon in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 5Last Post: 02-24-2007, 09:24 AM
Tags for this Thread