Results 1 to 5 of 5
06-17-2013, 08:44 PM #1
- Join Date
- Oct 2007
- Ellijay, GA
Torsion bar lifting...how much is too much?
I have a 1999 K1500 Suburban that's pretty much stock at this moment. I just purchased some 2007 Silverado factory rims that are 17', where as my originals were 16". I want to add some lift but not a ton, and I have heard/read that this can be easily accomplished with blocks in the leaf springs in the rear in conjunction with ratcheting up my torsion bars on the front. My question is how much lift can I achieve on the front safely, without damaging any suspension or drive train components. As little as 1.5-2.0" would be enough for the look I want, am I ok doing this, or should I get a leveling kit with the torsion keys?
Thank you in advance for any input.
06-17-2013, 09:37 PM #2
I knew a guy who did about a six inch lift with just blocks and cranking the bars on that vintage burb. I have no idea how it handled, but he was happy with it and he's a long time car guy (works for a major auto parts chain)
'01 K2500 496 big block It's here! It's here! It's finally here!
06-17-2013, 09:48 PM #3
- Join Date
- Jan 2012
- New York
- Blog Entries
I do not know about a 99 year vehicle... but my 2009 gained about 1.5 inches with the stock keys turned all the way up. The main thing is when you crank them to be sure you maintain adequate clearence between all bump stops. I just upgraded my suspension adding two inches in the front and 2 in in the rear... this included new UCA's, keys, and 2 inch rear blocks. I made sure when I adjusted the keys to maintain 3/4 inch between the upper stop as I do not want the UCA's to get damaged.2009 Chevy Silverado 2500HDLT 6.0L w/ Towing Package, Dick Cepek GM8 Rims, Dick Cepek FC II 33X11.50R17,RKSport Ram-Air Hood(Functional), Lazer Lite Aluminum Tonneau Cover, Road Armor Stealth Bumper, PIAA Lighting, Diablo Trinity Tuner, Diablew Custom Tune, BullyDog Cold Air Intake, American Racing Headers w/highflow cats, Corsa Performance Sport Exhaust, Custom Striping, Black Bowties front and rear, Fuel Grille Inserts, Recon Headlights, Readylift Shocks, Readylift Upper Contol Arms, 2" Blocks in the Rear..
Future Plans: HD Tie Rods, Under hood upgrades, Crower Camshaft and possibly electric fans.
06-18-2013, 05:53 PM #4
Not sure how much you can raise the front but you need to watch the ball joints for binding.2011 Chevy Silverado LT 4WD 25k miles
2001 Suburban 2WD, 5.3, V8 176k miles
06-21-2013, 12:10 PM #5
they're not meant to be above 3"
a good way to tell is looking at your sway bar end-links
the sway bar should be level to the ground... if your end-links are straining and stretching, and lowering your sway bar's ends... its too high, and your suspension is going to hyper extend, and wear faster.
I lifted mine 3" then snapped an end link when I was off-roading. so now its at 2" with new, longer end-links.Gas was $1.83 when Obama took office.....
By Rickd106 in forum Lifted & Offroad SuspensionReplies: 2Last Post: 10-15-2010, 06:46 PM
By muddmonkey in forum Chevy S10 Forum (GMC Sonoma)Replies: 8Last Post: 07-17-2010, 03:24 PM
By dougmc in forum Chevy Silverado Forum (GMC Sierra)Replies: 0Last Post: 04-24-2010, 09:26 AM
By 93GMCnugget in forum Lifted & Offroad SuspensionReplies: 3Last Post: 07-25-2009, 11:05 AM
By L0sts0ul in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 6Last Post: 02-22-2007, 06:41 PM
Tags for this Thread