Results 1 to 10 of 10
09-05-2013, 12:53 PM #1
What's up with brake pad manufactures?
I have noticed over the last few years that when I install new pads I have to go at the ears of the pads with a file. They fit so tightly that you would have to beat them in if you did not file them down. The last set that I installed I had to spend a pretty substantial amount of time filing them so they would slide properly. I have noticed this with multiple manufactures and over multiple vehicle manufactures. Are their tolerances that far off that what they are selling is acceptable? I have also heard that Wagner no longer has a lifetime warranty. They will replace your pads one time for free. I was told that they are doing this because of taxi drivers and other industrial users going thru pads on a constant basis. I know that I saw @j cat mention filing pads down in another post. Has anyone else noticed this?
1995 Silverado 4x4
6" BDS Suspension Lift-3" Body Lift-Add A Leaf in rear -Trailmaster SSV Shocks-Duel Steering Stabilizer Kit -AirAid Cold air intake-
4.56 Gears with Detroit Auburn Locker-Pro-Comp Traction Bars with duel shocks-Aluminum Skid Plate Kit-38.5" x 16.5" Mickey Thompson Baja Claws-Constant Dropping fuel gauge
2005 Yukon XL Jet Power Programmer, Bilstein Shocks, Bilstein rear springs, Helwig Anti-sway bars, EGR Window Visors, EGR Hood Shield, Denali Headlights, Headlight harness upgrade, GE NightHawk Bulbs, White Night Rear lighting system, Russell Braided SS brake lines, PowerStop Brake pads, PowerStop cross drilled and Slotted Rotors, http://www.gmtruckclub.com/forum/sho...5-GMC-Yukon-XL
2002 Silverado ext cab 2wd (Sold)
2003 Yukon XL (Totaled)
09-05-2013, 01:15 PM #2
I just replaced my front pads (and rotors) this past weekend. While they were a tight fit, I didn't need to file or modify anything to get them in. This is the second time I have replaced the pads on my truck and I didn't need to do any filing the first time either.Clint (TX) 2001 Silverado LS 4.8L auto 2wd ECSB [GARAGE]
Gasoline or gunpowder: If you ain't burning one, you ain't having fun!
NRA Endowment Member 5 24 48 88 - Hendrick Motorsports FTW!
09-05-2013, 01:23 PM #3
Last edited by Pikey; 09-05-2013 at 01:33 PM.
09-05-2013, 02:02 PM #4
Interesting. I installed Duralast pads this past weekend. They were a tight fit but no filing. All I had to do was make sure I was pushing in both ends of the pad at the same time and not let one end get ahead of the other.
09-05-2013, 06:28 PM #5
@Pikey, I've had the problem as well, on the last two, or three, sets of pads. I don't think I had to file all of the ears, but one, or two on an axle set.Ray
'09 Avalanche LTZ - Black
'05 Envoy XL (sold)
09-05-2013, 06:37 PM #6
- Join Date
- Apr 2013
- East Central Iowa
I have also seen this. I think the punch press or what ever they use to make the steel plate needs new cutters more often.
09-05-2013, 10:34 PM #7
It's not just the stampings that seem to be getting out of tolerance. I recently replaced the front disc pads on my wife's minivan. After installing the new brakes, their was still a very noticeable squealing coming from the driver's side. Turns out that the "tattle tale" tab that is bent first up, and then back down towards the rotor was sitting too high. It was rubbing against the wheel as it rotated past the brake pad, causing it to squeak and squeal. Never had that problem before this last time.csltrains96
Myself, my beautiful wife
3 - boys
3 - minivans
1 - '89 Chevy K2500 Silverado Truck
1 - 27 foot travel trailer
Not enough family time!
09-06-2013, 07:29 AM #8
I always grind the edges and put on copper anti-sieze when I dod them on any car. I noticed on the Silverado, the corrosion caused the retainer springs to stick and I had to grind them again to make them fit in properly even though they already had 25K on them. The minimal clearance and a little corrosion and it always needs a good grind off even for new ones.
09-06-2013, 08:28 AM #9
09-06-2013, 09:51 AM #10
I am glad to find out that is not just me having this issue.
Tags for this Thread