Results 1 to 10 of 10
Thread: Bump Stops on '96 Tahoe
10-19-2013, 01:47 PM #1
Bump Stops on '96 Tahoe
So I've been looking every where on and off for months and have yet to find new bump stops from my truck. All 4 have rotted out and now put the truck at risk of potential damage if it hits a really hard bump or reaches its max suspension travel. I have checked all over amazon, Energy Suspension, and Autoanything, but have either come up with overly expensive products that I'm not even sure will work or well nothing. Even GM doesn't have the part from what I can find. I really don't care if they are after market or factory I just want to find decent stops at a good price, less than 30 for a pair. Here are pictures of whats left of my factor ones.
1996 Chevy Tahoe LT 5.7L V8 4X4 205,000+ miles. Built proudly at Janesville Assembly in Janesville, Wisconsin
Basic mods: Lights all over, bunch of electrical work, and a couple cooling mods.
Check out my other mods in My Garage: http://www.gmtruckclub.com/forum/sho...t-Tahoe-4-Door
10-19-2013, 04:08 PM #2
Try looking at Energy Suspension and Moog, both have urethane replacements priced around $18.00 per set of 2.
10-19-2013, 04:30 PM #3
- - - Updated - - -
Ok Found possible front one but yet to find a rear one, to be honest I have no clue what the factory ones look like.
Here front one: http://www.energysuspensionparts.com...sp?prod=9.9150
10-19-2013, 04:38 PM #4
If it fits a 1/2 t truck it fits your Tahoe.
Even though many suspension part numbers for tahoes are different theyre interchangable with parts for on trucks.
Many aftermarket bumpstops arent direct replacement, they require you to.drill holes and install self tapping bolts.
But considering the condition ob fasteners and mounting point many times before replacing bumpstops thats not always a bad thing.
I could point yours out as a prime example of this!
10-19-2013, 04:53 PM #5
10-19-2013, 05:21 PM #6
Your fasteners (bolts) and the spots their bolted into, in this case with self tapping fasteners into holes in the frame, look real corroded.
More than likely when you remove the fasteners the holes are gonna be corroded and youll probably need to drill new holes next to them to put the new fasteners in.
I wouldnt be surprised if you have problems getting the fasteners out.
In the past working on parts in this condition Ive either chiseled the bolts off or torched them out, the either tack the new bumpstops on with a Mig welder or drill new fastener holes.
10-19-2013, 05:35 PM #7
Yah fasteners on this truck are not my friend.... They all are un coated with a protective material and most have rusted together. I'm wondering if I can clean up the rear bump mounts and find a way to reuse them to attach the new stop. I'm luch many parts are held on with a nut and bolt not just self tapping.
10-19-2013, 06:35 PM #8
The new bumpstops will come attached to a plate that bolts where your present plate is.
Energy Suspension uses plates that have a corrosion coating, not a perfect coating but marginally better than factory paint.
In this case self tappers could be your friend, if they refuse to back out smack'em with a chisel then whack the rest out of the frame with a punch, get a self tapping screw one size larger and run it in.
Do yourself a favor and clean/coat the area under and around with paint or a coating, after bolting in the new bumpstops cover their fasteners too.
10-19-2013, 06:45 PM #9
Do you have any paint recommendations? If you do, can you PM them to me so not to detract the thread to much.
10-19-2013, 07:11 PM #10
- Join Date
- Dec 2004
- Arlington, Texas, United States
- Blog Entries
What year range should be good for that Tahoe?
10 Chevy Traverse LT AWD
02 Chevy Trailblazer LS (110K+ miles - loaded except for 4WD - WRECKED!)
99 Chevy Cavalier LS (105K+ miles - commuter car)
78 Chevy Suburban Silverado (454, 3/4 ton)
62 GMC 3/4 ton Pickup (350 police interceptor)
Remember: Search Before Posting | Fill out Your Profile & Signature
* I've been saying for years that I was going to change my username, and I finally did.
Tags for this Thread