GM Truck Club
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 3 of 3
  1. #1

    Default Novice question about 2002 Tahoe trans. Would you try this?

    I purchased my 02 Tahoe used. One owner, but ran hard. It is 4WD, has a 5.3 Vortex, tow package, and 148K in miles. I change my own oil and filters, and plugs and wires. Beyond that, I am not very comfortable. Friend of mine said the trans fluid and filter needed changing. He said fluid was not "clean enough" or "it's not pink enough" I would be willing to bet it has never been changed. Local quick lube said they would do "a transmission Backflush" for $99.95, and the pan need not be dropped, or filter changed. If you were me, knowing how little experience I have, would you try the job yourself, filter and all? Or would you pay someone to do it. I am short on money, but good with time. If you think this is a job I can do, where can I find good instructions on the net? Thanks

  2. #2


    you can do it. It just takes patience and a lot of rags! Chances are that you will spill fluid all over your garage floor. Sure, your pan may have a drain plug in it. But, I have never been able to get one out successfully. I have been told that you need to remove the pan and heat them up to break them loose. I do not believe in back flushes. Some say that it can move contaminants that are sitting in a spot where they are not causing hard to a spot where it will cause harm. Plus, that does not change the filter. It is pretty basic to do. You may have to remove the trans shift cable bracket from the side of the trans as it covers part of the pan. Drop the pan. Pull out the filter. Clean everything up very well. Put the new gasket on, install the new filter and reinstall the pan. (Some guys are totally against using any kind of gasket sealer on the gasket. I do not use any on a rubber gasket, I will use a thin layer on the mating surfaces of with a cork gasket.) You need to make sure that you do not over tighten the pan bolts. You can break them or smash the gasket and have a leak. Also, make sure that you don't reuse dextron III. I think that the new stuff is dextron IV or V. @j cat might be able to clarify what the proper fluid to replace it with is.

    So, really there are a couple key things you need to remember
    1)Clean the mating surfaces well
    2)Do not over tighten.
    3)Fill to the correct level. DO NO OVERFILL!!

    here is a vid: it is for a hd. But, gives you the idea.
    Last edited by Pikey; 10-21-2013 at 09:36 AM.

    1995 Silverado 4x4
    6" BDS Suspension Lift-3" Body Lift-Add A Leaf in rear -Trailmaster SSV Shocks-Duel Steering Stabilizer Kit -AirAid Cold air intake-
    4.56 Gears with Detroit Auburn Locker-Pro-Comp Traction Bars with duel shocks-Aluminum Skid Plate Kit-38.5" x 16.5" Mickey Thompson Baja Claws-Constant Dropping fuel gauge

    2005 Yukon XL Jet Power Programmer, Bilstein Shocks, Bilstein rear springs, Helwig Anti-sway bars, EGR Window Visors, EGR Hood Shield, Denali Headlights, Headlight harness upgrade, GE NightHawk Bulbs, White Night Rear lighting system, Russell Braided SS brake lines, PowerStop Brake pads, PowerStop cross drilled and Slotted Rotors,
    2002 Silverado ext cab 2wd (Sold)
    2003 Yukon XL (Totaled)

  3. Likes 99'HEARTBEAT liked this post
  4. #3


    Always be careful when you get to the last few bolts as you're dropping the pan because if you don't leave a few too keep it on you'll drop it and likely cover your self in ATF. Had it happen on my friends Sable, ATF doesn't taste very good and it ruins white clothing (other friend helping was in all white). The only worry with just dropping the pan is you don't get all the ATF out there will still be a lot in the torque converter.

    The new fluid is Dexron VI there's only a few licensed manufactures of it. The only one that is easy to find would be Valvoline who is licensed to make it and its sold at most auto parts stores.

    I've had a flush done on my truck by my shop which has a proper flush system and it worked great, but I had them also change the filter because the one in the tranny had 196,000 miles on it. I would not trust a quick lube shop to do the same service my shop did and I only trusted the shop to do it because the owner who has a Burb about the same age as mine has done it to his truck with no I'll effects. Plus the owner explained the whole process to me what it cleaned and how and then said he would do it him self on my truck to make sure it was done perfect.

    1996 Chevy Tahoe LT 5.7L V8 4X4 205,000+ miles. Built proudly at Janesville Assembly in Janesville, Wisconsin
    Basic mods: Lights all over, bunch of electrical work, and a couple cooling mods.

    Check out my other mods in My Garage:

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts