Results 1 to 7 of 7
Thread: Adjusting timing
11-17-2008, 10:13 AM #1
As some of ya'll may know, I've been trying to get the motor in my Suburban tuned up and working at peak efficiency. Over the weekend I replaced the coolant temp sensor that wasn't working and replaced all the spark plugs with Autolite Platinums. Now after I buy and drop the hotter Accel or MSD coil in, I should be good to go. So, now to adjust the timing...
Referring to this thread: http://www.gmtruckclub.com/forum/showthread.php?t=14855 I have been trying to do a tuneup/performance mod that should yield better mpg and power. The spec for the plug gapping was .035", however, the plugs came from the store gapped at .045" and I thought that would be a good starting point to widen the gap. At idle it seems to run well so far, no missing or anything, most likely due to replacing the plug that had chipped porcelin on the insulator (one of the previously dead cylinders). So, I'm going to drop a MSD or Accel high-volt coil in to make sure the spark can easily jump the gap and then I want to bump the timing. Well, I'm not quite sure how I can do it and find the butter zone easily. I know with older carb'd motors you hooked a vacuum gauge up to the intake vacuum and adjusted the timing and carb until you got the highest readings. However, this is a Throttle-body injection intake system, so it's half-carb half fuel injected.... I don't know where to start. So, how can I evaulate how close I am to getting it right while it's idleing in the driveway. I'd like to avoid having detonation when I'm trying to accelerate on the interstate
PS: What does pinging/spark knock/ detonation sound like? I've never heard it before as far as I know, and I would hope it's not loud enough to hear while driving...Christopher
1991 Chevy Suburban 1/2 ton 2WD w/ chevy SBC 350-3/4 ton drivetrain upgrade w/4.10 gears 200K miles
2005 Saturn ION-2 Stock 265K miles
1982 Bronco, 1993 Bronco (sold), 1971 M35A2 Deuce and a Half
There are 10 kinds of people, those who understand binary, and those who dont...
Remember kids, the only difference between screwing around and science is writing it down- Adam Savage
11-17-2008, 10:41 AM #2
Im not sure exactly how to adjust the timing on the TBI motors, but I know you need to unplug a certain wire or you will be fighting the computer. As far as what detonation sounds like, it will make your Suburban sound like it is diesel powered.Gary
99 K 1500 Suburban
78 Silverado Big 10 w/factory 454
00 S-10 Blazer
1976 Trans Am
1980 Honda CB900 Custom
11-17-2008, 12:19 PM #3
I read the sticker on the core support for the radiator and found the plug to disconnect to drop back to base timing. I'm just trying to figure out how to know in the shop when I've got it set right. I've been told that just by sound you should be able to tell. However, I've never tried and I don't want to screw it up too much.
11-17-2008, 12:27 PM #4
Use a timing light and just add 2 more degrees to the factory setting.
11-17-2008, 12:31 PM #5
only 2 degrees? for the broncos they're knocking them back 5-7 usually...
11-17-2008, 12:38 PM #6
GM you advance the timing for more power. Without getting into all types of performance issues adding just 2 degrees is enough.
11-17-2008, 01:07 PM #7
so I should advance it to 2 degrees BTDC. OK, we'll see what happens. I definitley want to achieve max mpg and if power comes along with it, so much the better
By jjjg_02 in forum General Chevy & GM Tech QuestionsReplies: 1Last Post: 12-08-2009, 05:07 PM
By safetyfast in forum General Chevy & GM Tech QuestionsReplies: 3Last Post: 06-06-2009, 05:43 PM
By bigburb in forum GM PowertrainReplies: 2Last Post: 05-10-2009, 05:26 PM
By bensdive in forum General Chevy & GM Tech QuestionsReplies: 2Last Post: 05-15-2008, 07:28 PM
Tags for this Thread