Results 1 to 8 of 8
02-19-2009, 01:18 PM #1
Grill, parking and headlight removal - '99 Suburban..
Please tell me what other years and model trucks this would apply for so I can update the subject! Thanks!
How to remove the grill
How to remove the parking lights
How to remove the headlights
...or just change the bulbs.
Parking lights - removal and bulb change
Very easy to do. With a Phillips head screwdriver, take off the four screws on each of the four corners of the parking lights.
The assembly will come out easily and the two bulbs in the rear can then simply be twisted and pulled off to replace, or both taken off to remove the parking light assembly.
Last edited by Springthing; 02-19-2009 at 01:38 PM.
02-19-2009, 01:24 PM #2
Remove the screws along the top of the grill. There are four total, two on each side, and two along the rail front.
Remove the screw through the front of the grill.
Last edited by Springthing; 02-19-2009 at 01:39 PM.
02-19-2009, 01:32 PM #3
With the screws removed, CAREFULLY either reach down or, with the aid of some tools (hanger and metal rod?), work them down to where you can lift up on the tabs that hold the grill in place. Lifting the tab and pushing gently on the grill should be enough to pop it loose.
Below shows the tongue on the grill that fits latches onto the tabs in the above picture.
Once the grill has been freed, twist and pull to take the corner lights out of their housing, visible on the bottom right of the above picture. Replace bulbs that are burned out.
At this point your front end should look like:
Last edited by Springthing; 02-19-2009 at 01:40 PM.
02-19-2009, 01:37 PM #4
Removing headlights / Changing headlight bulbs
Removal of the headlight assembly, like everything else, is rather easy.
Four bolts hold the assembly in place. Remove the four bolts - support the assembly while removing the last of the four.
As with all other lights, simply twist and pull out to remove the bulbs.
With all these steps followed, you should now have this view... ready to reverse the steps for installation (or bolting on of a new grill!)
Last edited by Springthing; 02-19-2009 at 01:41 PM.
02-19-2009, 04:01 PM #5
- Join Date
- Feb 2007
- Blog Entries
Awesome! You have no idea how long my uncle and I spent trying to get the front grill off his dually. If we'd had these directions, it may have taken 10 minutes.Christopher
1991 Chevy Suburban 1/2 ton 2WD w/ chevy SBC 350-3/4 ton drivetrain upgrade w/4.10 gears 200K miles
2005 Saturn ION-2 Stock 277K miles
1982 Bronco, 1993 Bronco (sold), 1971 M35A2 Deuce and a Half
There are 10 kinds of people, those who understand binary, and those who dont...
Remember kids, the only difference between screwing around and science is writing it down- Adam Savage
02-19-2009, 04:11 PM #6
Well.... you should have just asked!! LOL
02-26-2009, 09:28 AM #7
Great post! This will help as I stripped out the screw pin that releases the headlight for quick bulb change and so I can paint my grill. My only question is do you think the grill can be removed with the brush guard still on or should that come off too?99 K1500 Suburban LT "THE BEAST"
Hypertech III, K&N, true dual
02-26-2009, 08:09 PM #8
You'll need about 3 or 4 inches or so to pull the grill forward to pop it off the bottom tabs. Might be lucky if you have that or a little less...
By ARCTICFRONTIER in forum General Chevy & GM Tech QuestionsReplies: 2Last: 01-28-2010, 01:48 PM
By Jimzu in forum Lifted & Offroad SuspensionReplies: 2Last: 07-15-2009, 07:12 PM
By helomech09 in forum General Chevy & GM Tech QuestionsReplies: 3Last: 07-15-2009, 02:43 PM
By Derwood in forum Chevy C/K Truck ForumReplies: 1Last: 04-12-2009, 12:12 AM
By ODogg in forum Chevy Truck AccessoriesReplies: 2Last: 06-21-2008, 08:45 AM
Tags for this Thread