Results 1 to 7 of 7
Thread: Need brake setup suggestions
03-02-2009, 07:24 AM #1
Need brake setup suggestions
It's time to replace rotors and pads on my 04 Silverado.
I'd like to increase braking performance without having to change calipers, or tire size.
I've read negative and positive posts about drilled, slotted, cross drilled, and drilled/slotted rotors.
Anyone have anything constructive to mention in here? Reason for the upgrade is that I'm going to be hauling a trailer for most of the spring / summer, and it's always better to stop quicker.'04 Silverado Z71 Special Edition
'81 Camaro - 400 SBC - 30 Over - th350 w/Stage II shifter - 4.10's
'70.5 Camaro - Bone Stock
'75 Porsche 914
'27 Model T
03-02-2009, 08:45 AM #2
I would suggest going with one of the configurations you mentioned, just for the added heat dissipation. If you're worried about warpage and weakening of the rotor due to cross drilling, then get dimpled. You'll also want a rotor that has a good internal vein design as this will further increase heat dissipation. And remember to get decent pads.
03-02-2009, 08:46 AM #3
idk about drilled and slotted rotors haven't seen them on a truck before i would just get the extreme duty pads and rotors
2003 Z71 Silverado LS
Access roll up cover
Billet Grill insert
CB with PA system
Waiting to be installed
Two 8in RF HX2 punch( would have 12s but they got stolen)
03-02-2009, 10:20 AM #4
What I've heard is that the slotted rotors wear out the pads much quicker then simply the cross drilled / drilled. Can anyone atest to this?
As far as the extreme duty goes, is that what is found on an HD truck? I haven't heard of this before.
Would a 1500HD rotor and pads fit a regular 1500 caliper and hub?
03-02-2009, 10:27 AM #5
- Join Date
- Jan 2007
- Yacolt, Washington
- Blog Entries
This weekend I installed a SSBC Brake kit with slotted rotors and premium pads on all 4 wheels that came as a complete kit from Autoanything.com. It was around $459 (free shipping) and my Wife is very impressed at how well her suburban stops now.
Last edited by dwill3015; 03-02-2009 at 10:30 AM.Darcy
2006 Silverado 2500HD LT3 4X4 CC SB Duramax LBZ
Tuff Country 6" lift, 35" Toyo M/T's on 20" Ultra Peacemaker wheels, Quadzilla Stealth2 programmer, Diamond Eye 5" cat-back exhaust, factory Special order color Yellow.
03-04-2009, 08:44 AM #6
Well, I've decided to go with a set of EBC Yellow Stuff pads.
They are supposed to have the greatest bite of the EBC pads.
I took a look at my rotors, they look to be fine, I don't experience any play in the pedal from a warped rotor, so I think I'm just going to hit the pads for now.
Thanks for the input, I think SSBC is the way to go when I put the lift on and the 20's though, seem to have a great product.
03-04-2009, 09:06 PM #7
- Join Date
- Dec 2008
I felt the same way about the brakes on my '04 1500, so I found these on E-bay, and I thought I'd give them a try:
They sell a complete package of four, zinc-plated, cross-drilled and slotted rotors and ceramic pads for the front and rear for $256, with free shipping. The only thing not included are the rear brake shoes for the parking brake.
So far, I have swapped the front rotors & pads and did the proper break-in on the new pads & rotors and intially, they didn't feel any stronger than stock, but after a few hundred miles, they feel much better and seem to stop stonger than stock. I haven't done any seriously hard driving or long distance towing downhill to test their resistance to fade, but the rotors should resist fade much better than the non-drilled stock rotors.
As soon as I get the shoes for the rears, I'll swap out the rears and report back in a month or so, when I have a more than a thousand miles on them.
So far I very happy with the new setup.
By drakeoz71 in forum General Chevy & GM Tech QuestionsReplies: 4Last: 04-24-2010, 05:24 PM
By pcs9449 in forum Lifted & Offroad SuspensionReplies: 0Last: 04-19-2010, 12:18 AM
By 951500 in forum General ClassifiedsReplies: 0Last: 12-05-2009, 04:46 PM
By Fe Fanatic in forum Chevy C/K Truck ForumReplies: 2Last: 10-25-2009, 04:52 PM
By akagun in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 4Last: 02-04-2009, 09:44 PM
Tags for this Thread