Results 1 to 7 of 7
Thread: Ignition stuck in "ON" position
04-29-2009, 04:20 PM #1
Ignition stuck in "ON" position
Well, I went to the store and when I got there, I couldn't turn the truck off. Obviously I just went home, but I had to pull a fuse to turn the motor off and it seems that I'm going to have to disconnect the battery too if I don't get this figured out.
When I left for the store, I remember that it was hard to shift out of Park, but it went without forcing it. Maybe I broke something? I can't even see how to get to the steering column, do I have to pull the steering wheel?
04-29-2009, 05:31 PM #2
That's weird. It happened to my jeep once. The ignition was shot and I was using a screwdriver to start it. Well, that only worked for so long. The last little piece that the screwdriver was catching stripped off and It got stuck running with the starter engaged. Even after I pulled the batter cables it was still running.Dan
1999 GMC Sierra 2500 350 vortec
1967 Jeep M725 ambulance 230 tornado
1990 Cherokee Limited- 3 inch lift on 33's
...and every one of em has issues
If you have any questions or problems don't hesitate to send me or any other GMTC moderators a PM
04-29-2009, 05:34 PM #3
Yeah, disconnecting the battery when it's running shouldn't make a difference. At that point the truck should be running off of alternator power. I'm just worrying how much this is going to cost to fix.
I'm guessing that the ign. cylinder is bad, but I just want to make sure that I didn't possibly break something else. I guess I'll have to pull out the manual to see if it says how to switch it out.
04-29-2009, 05:35 PM #4
- Join Date
- Feb 2007
- Blog Entries
This happened in my Saturn. Turns out some cap on the back of the ignition switch fell off. That somehow kept it from going into the lock position and wouldn't let the key go. Until I could get it in the shop, I manually locked the doors, pulled the fuel injector fuse to turn the car off, and pulled the battery cable when I wasn't driving the car. Worked OK, albeit "ghetto".
EDIT: Switching the ignition cylinder out shouldn't be too hard unless your steering wheel has an airbag. After I figured out how to do it the first time, I'm able to strip my steering column down in probably 30 mins which is going past the point where you take the ignition cylinder out.Christopher
1991 Chevy Suburban 1/2 ton 2WD w/ chevy SBC 350-3/4 ton drivetrain upgrade w/4.10 gears 199K miles
2005 Saturn ION-2 Stock 255K miles
1982 Bronco, 1993 Bronco (sold), 1971 M35A2 Deuce and a Half
There are 10 kinds of people, those who understand binary, and those who dont...
Remember kids, the only difference between screwing around and science is writing it down- Adam Savage
04-29-2009, 05:42 PM #5
04-29-2009, 09:48 PM #6
04-30-2009, 10:12 AM #7
You will need a steering wheel puller and a lock plate tool. You should be able to get those at you local parts store and maybe even on a "loan-a-tool" program.
99 K 1500 Suburban
78 Silverado Big 10 w/factory 454
00 S-10 Blazer
1976 Trans Am
1980 Honda CB900 Custom
By unplugged in forum Sports & OutdoorsReplies: 59Last Post: 07-18-2012, 09:14 PM
By xycarp in forum Wheels & TiresReplies: 2Last Post: 05-31-2010, 10:38 AM
By Steve in forum Other GM CarsReplies: 0Last Post: 06-21-2008, 01:30 PM
By Steve in forum The Coffee Shop ~ Chit ChatReplies: 0Last Post: 07-24-2007, 01:30 PM
By Cableguy in forum The Coffee Shop ~ Chit ChatReplies: 0Last Post: 04-27-2007, 11:47 PM
Tags for this Thread