Results 1 to 4 of 4
Thread: Unusual Brake problem
08-03-2009, 10:47 AM #1
Unusual Brake problem
This morning on my way to work my brakes started to malfunction.I would breifly touch the brakes and they would almost "lock up",then they would be all "Spongy" and the brake warning light would come on.
This is in a 1990 Chev Suburban 6.2 Diesel 2500.I checked the Brake fluid level and it is fine.Also I checked the hoses for any leaks,again all in order.The Brake Fluid is quite dirty,I will flush the system this weekend.
I was wondering if there is a load sensor on the system that might be problematic.Somthing that increases your Braking power when you are towing for example?When the brakes are vauge the limited brakeing power seems well distibuted around the car.So my guess is its a technical fault rather than a mechanical one?
All input is appreciated.
08-03-2009, 11:38 AM #2
- Join Date
- Feb 2007
- Blog Entries
There was a RABS (rear ABS) system in 1990, and that might be your culprit. There is a way to check the RABS computer codes. It's shorting out a different pin in the OBD connector to ground and then counting the flashes. Sadly, I don't remember which wire it was off-hand. It could be that something's going wrong with the RABS and the computer for it's just giving up and shutting down. Make sure you get this issue resolved before taking it back out on the road.Christopher
1991 Chevy Suburban 1/2 ton 2WD w/ chevy SBC 350-3/4 ton drivetrain upgrade w/4.10 gears 199K miles
2005 Saturn ION-2 Stock 255K miles
1982 Bronco, 1993 Bronco (sold), 1971 M35A2 Deuce and a Half
There are 10 kinds of people, those who understand binary, and those who dont...
Remember kids, the only difference between screwing around and science is writing it down- Adam Savage
08-07-2009, 01:40 AM #3
I had an issue similar to yours but only after I'd let the thing sit for 2 weeks When I started to drive it the brakes were dangerously sensitive and hard to gauge and then became spongy. This continued for about a half a block and went away. I used a code reader and nothing came up so I took it to the brake shop and they couldn't find the cause nor dupicate the condition. It hasn't occured since and I've experienced no other problems. Please post an update if you find the cause.
1989 R1500 Silverado Suburban
5.7L, TBI w/ Dual remote oil filters,
16" 2010 CFM E-fan, K&N filter
TH700R w/ Aluminum pan, remote trans fluid filter and aux trans fluid cooler
Air shocks rear,
7x16 dual axle cargo trailer; 10K Reese HD trunnion bar WDS, dual friction sway dampeners
Cuz....I like to move it, move it....
08-07-2009, 11:48 PM #4
the abs system is a good starting point the rear brakes set the pedal height try a mighty vac brake bleed and flush it out might clear up
99 tahoe 2 dr. 4x4 7.4 4L80-e NP246, SAS, dana 60 hp, sterling 10.5 rear, gibson headers, and alot of tricks of the trade !!!!!!IF YOU'RE NOT CHEATING YOUR NOT TRYING!!!!!!!!
By sharpshooterusmc in forum Lifted & Offroad SuspensionReplies: 4Last Post: 03-21-2010, 01:54 PM
By Steve in forum Hummer ForumReplies: 0Last Post: 12-30-2009, 08:30 PM
By Tarsis in forum Lifted & Offroad SuspensionReplies: 7Last Post: 04-27-2009, 08:05 AM
By dwcruz in forum General Chevy & GM Tech QuestionsReplies: 5Last Post: 03-17-2009, 12:47 PM
By garrison in forum Member IntroductionsReplies: 5Last Post: 05-28-2007, 10:00 PM
Tags for this Thread