GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 5 of 5

Hybrid View

  1. #1

    Default Chevy Suburban Keyless Remotes and Remote Programming

    2005 Chevy Suburban Keyless Entry Remote fob programming instructons

    1. Close all vehicle doors.
    2. Insert the key into the ignition.
    3. Hold down the power UNLOCK button on the driverís door panel-continue to hold down until instructed
    to release in step 9.

    4. Perform steps 5 through 8 in fairly rapid succession.
    5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
    6. Turn the ignition switch to the OFF position.
    7. Turn the ignition switch to the ON position.
    8. Turn the ignition switch to the OFF position.
    9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
    10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks.
    This step may take up to 30 seconds.

    11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
    12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

    Steve
    10 Chevy Traverse LT AWD
    02 Chevy Trailblazer LS (110K+ miles - loaded except for 4WD - WRECKED!)
    99 Chevy Cavalier LS (105K+ miles - commuter car)
    78 Chevy Suburban Silverado (454, 3/4 ton)
    62 GMC 3/4 ton Pickup (350 police interceptor)

    Remember: Search Before Posting | Fill out Your Profile & Signature
    * I've been saying for years that I was going to change my username, and I finally did.

  2. #2

    Thumbs up

    Thanks for the programing, it worked like a charm!

    Phil
    Happy 2 Wheeler!

  3. #3
    Former Member
    Join Date
    Oct 2007
    Location
    Huntsville, Alabama
    Posts
    372

    Default

    Quote Originally Posted by Steve View Post
    2005 Chevy Suburban Keyless Entry Remote fob programming instructons

    1. Close all vehicle doors.
    2. Insert the key into the ignition.
    3. Hold down the power UNLOCK button on the driverís door panel-continue to hold down until instructed
    to release in step 9.

    4. Perform steps 5 through 8 in fairly rapid succession.
    5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
    6. Turn the ignition switch to the OFF position.
    7. Turn the ignition switch to the ON position.
    8. Turn the ignition switch to the OFF position.
    9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
    10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks.
    This step may take up to 30 seconds.

    11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
    12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.
    Do you think this will work with a 99 Silverado? My uncle dropped my remote in the toilet, luckily the battery was dead.

  4. #4

    Lightbulb

    Do you if it has roaming code like the late ones? It may be like my 97, try holding the remote close to the vehicle then press & hold both lock & unlock buttons at the same time for about 30 seconds.

    Phil

  5. #5

    Default

    Quote Originally Posted by Steve View Post
    2005 Chevy Suburban Keyless Entry Remote fob programming instructons

    1. Close all vehicle doors.
    2. Insert the key into the ignition.
    3. Hold down the power UNLOCK button on the driverís door panel-continue to hold down until instructed
    to release in step 9.

    4. Perform steps 5 through 8 in fairly rapid succession.
    5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
    6. Turn the ignition switch to the OFF position.
    7. Turn the ignition switch to the ON position.
    8. Turn the ignition switch to the OFF position.
    9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
    10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks.
    This step may take up to 30 seconds.

    11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
    12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.
    Following your instructions to reprogram the keyless entry for a 2002 Chevy Suburban, I went through all the steps and the door locks recycled after step 10. However, the keyless entry still would not work. Any suggestions?

    Thanks

Similar Threads

  1. Chevy Silverado Keyless Entry Remote Programming
    By ChevyFan in forum Chevy Keyless Entry Remotes
    Replies: 16
    Last: 05-01-2013, 08:19 AM
  2. Chevy Suburban Keyless Entrying Remote Programming
    By ChevyFan in forum Chevy Keyless Entry Remotes
    Replies: 7
    Last: 09-22-2009, 04:33 PM
  3. 2007 Chevy Surburban Keyless remote programming
    By TomsHHR in forum Chevy Keyless Entry Remotes
    Replies: 1
    Last: 01-18-2008, 07:24 PM
  4. Chevy HHR Keyless Entry Remote Programming
    By TomsHHR in forum Chevy Keyless Entry Remotes
    Replies: 0
    Last: 08-09-2007, 10:09 PM
  5. Chevy Colorado Keyless Entry Remote Programming
    By ChevyFan in forum Chevy Keyless Entry Remotes
    Replies: 0
    Last: 07-30-2007, 10:25 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •