GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 10 of 10

Hybrid View

  1. #1

    Default 8 Lug 3/4 ton rearend

    I have an 87 Suburban and I just picked up the complete rearend from an 84 Chevy Truck that was at a junkyard. I also got the leaf springs bcuz they had 7 leafs and mines has only 5. (It's a half ton) And when we were taking off the parts, we noticed that the donor truck had a dual driveshaft setup and my Burbie is a straight through axle. I didn't pick up the dual setup bcuz I plan on trying 2 either use mine, or go to another yard and find drive shaft from another Burbie that has the 8 lug rearend on it already. Any suggestions?

  2. #2

    Default

    What driveshaft length do you need?
    I think the 2 piece driveshaft is a different length than yours.

    Check the U-joints out also, if that new axle was from a 3/4 ton and you have a 1/2 ton Suburban theres a differenc in U-joint sizes, Google "Spicer U-joints" they recently put out a line of U-joint adaptors for swaps just like yours.

    Watch those leaf spring lengths, I dont remember them being the same length either.
    Also something about them rubbing on the stock exhaust.

  3. #3

    Default

    Ok thanks. I heard that the leaf's should fit and as for them hitting my exhaust, I have a flowmaster that has no piping 2 it so that's not an issue. And I took the U- joints from the donor vehicle. Anymore advice?

  4. #4

    Default

    Started to mention spring perch width, but then I re-read and saw it was a 3/4 to 1/2 swap.

    Nevermind.
    Last edited by Willie G; 01-02-2010 at 08:47 PM.

  5. #5

    Default

    Yea, my truck is a 1/2 ton and I'm putting 3/4 ton parts on it. The springs seemed to be the same width where they are mounted at.

  6. #6

    Default

    You might need to put a manual BPV on the rear brakes.
    Your going to larger shoes with the new rear axle (which is a good thing) but the factory master cylinder and BPV dont know this and are set-up for the original axle.

  7. #7

    Default

    Quote Originally Posted by Willie G View Post
    Started to mention spring perch width, but then I re-read and saw it was a 3/4 to 1/2 swap.

    Nevermind.

    Shouldnt that say 1/2 to 3/4 swap ?????????????????????????

    1996 Suburban K3500 SLT DUALLY
    1988 Camaro RS 383 stroker LT1
    1992 32' Aero-tek Race Boat, 600 CI BBC
    WE CAN STICK A DIESEL IN ANYTHING
    SPECIALIZED IN CUSTOM CONVERSIONS OF ANY KIND
    Scott:glasses:

Similar Threads

  1. 99 rearend
    By d55gmc in forum Chevy Suburban Forum (GMC Yukon XL)
    Replies: 3
    Last Post: 07-27-2010, 11:33 AM
  2. Starter and rearend help 99 4X4
    By deancf in forum General Chevy & GM Tech Questions
    Replies: 4
    Last Post: 10-14-2009, 09:27 AM
  3. Rearend out of alignment.
    By plumber_rob in forum Lifted & Offroad Suspension
    Replies: 0
    Last Post: 08-24-2009, 07:55 PM
  4. rearend swap
    By ajfitz in forum Chevy Tahoe Forum (GMC Yukon, Cadillac Escalade)
    Replies: 2
    Last Post: 06-11-2009, 03:00 PM
  5. Is my rearend going out?
    By bcoffman in forum General Chevy & GM Tech Questions
    Replies: 16
    Last Post: 06-11-2009, 01:34 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •