Results 1,531 to 1,540 of 2390
09-27-2012, 01:59 AM #1531
- Join Date
- Jul 2012
Nothing special.I just clean it and get a long ride with a high speed.
09-27-2012, 06:10 PM #1532
Got her inspected and also installed some new windshield wipers (Rain-X) and topped off the washer fluid.Clint (TX) 2001 Silverado LS 4.8L auto 2wd ECSB [GARAGE]
Gasoline or gunpowder: If you ain't burning one, you ain't having fun!
NRA Endowment Member 5 24 48 88 - Hendrick Motorsports FTW!
09-27-2012, 09:11 PM #1533
not today, but yesterday....
was on a work detail pulling out some old PT equipment. came to the conclusion digging it all out by hand with a shovel (30 some odd posts, most at least 3 feet down, and concrete!) was gonna take WAY to long, so my truck got a bit of a work out pulling em out. most we had to dig a little to loosen em up, wrapped the chain on em and out they came. had I had better traction (loose dirt/sand) we may have just been able to jerk em out. 4x4 high and a good tug was enough on most of em, some took a few pulls. I didnt romp on it to much due to traction issues and not wanting to bend things up on my truck.... did get one pic ill post if anyone wants to see it, not the best tho (i didnt take it)
2011 GMC Sierra SLE 5.3 Z71 4X4 Stealth Gray Metallic
Tow mirrors - Diablew Tuned - Flowmaster Regular 40 - Ready Lift 2.5' lift - BFG LT A/T K/Os - Carr Light Wing - TruckLite LED lights - Optima Red Top - 50% Front Window Tint - Line-X bedliner - Aidaid MIT - Tekonsha P2 - ARS Billet Grill
09-28-2012, 02:42 PM #1534
Today I picked up a York 210L compressor w/ rotolock fittings for my OBA project.
09-28-2012, 03:06 PM #1535
I ground off the rivets holding the latch to the underbody tool box on the Duramax and pulled the latch out. Pried the door open (its a bit bent), did some grinding to make the newer stronger latch fit, some hammering to make the door fit, and bolted the new latch in. Now I have a nice working tool box under the deck, and its lockable. As a nice bonus, the truck came with a couple of spare fuel filters in the tool box.
2001 Silverado Reg. Cab Not-So-Base -- SOLD
2003 Avalanche Z71. No Cladding. Check out my Mod thread.
1974 Triumph Spitfire 1500 - Work in Progress
2003 Sierra 3500 Duramax. The Newer, Better Work Truck
09-29-2012, 10:41 AM #1536
Today I picked up a 6-groove clutch for my York 210 compressor.
09-29-2012, 07:45 PM #1537
Ordered an LM487 so I can finish my LED conversion with out those pesky resisters.
10-01-2012, 12:54 AM #1538
The part you need for your truck is an EP29L Led flasher. It's smaller and you should be able to get one for cheaper than the LM487.
10-01-2012, 03:45 AM #1539
Today I ordered a 0-400psi sending unit and Dakota Digital air pressure gauge for in-cab use with my OBA project.
10-01-2012, 10:59 AM #1540
By ZSI52 in forum General Chevy & GM Tech QuestionsReplies: 47Last Post: 09-03-2012, 02:32 PM
By pmf608 in forum Chevy Truck TalkReplies: 21Last Post: 07-25-2012, 11:53 AM
By texas99lb in forum Chevy Silverado Forum (GMC Sierra)Replies: 10Last Post: 01-06-2010, 02:13 AM
By Delmarva in forum Chevy Silverado Forum (GMC Sierra)Replies: 0Last Post: 11-11-2009, 12:39 PM
By etpn13 in forum GM PowertrainReplies: 2Last Post: 04-22-2009, 03:45 PM