Results 1 to 6 of 6
Thread: Removal of Broken bolts?
05-20-2010, 01:41 PM #1
Removal of Broken bolts?
Just wondering what you guys have done for tricks to remove broken bolts in the block. I have 3 manifold bolts that are broken off, both of the ones that are on the farthest most back of the manifolds, they're broken from a long time ago from GM's design, and also the very most front one on the drivers side, from me using a ratchet, instead of an air gun. I have heard of tricks of people using acetylene torches and heating them up red hot, then putting candle wax, or instead, then cooling them rapidly with ice. I've been soaking the bolts in WD-40 before work, and then after work to try and loosen the bind of rust. So hopefully this will help me. The only thing that's happened, is that the heads of the bolts have snapped off, they have a little bit of the stud still sticking out. So i was going to try and weld on a nut, then try and unbolt them like the other ones.
Anyone have any suggestions?
2002 Chevrolet Silverado 1500 z71 1985 Chevrolet Silverado k10 2006 Chevrolet Silverado 2500hd 6.6l LLY Duramax 6.5" BDS Suspension Lift Key'd to 9" Edelbrock Carb & Polished Intake Manifold & Valve Covers NAPC Race Transmission & NAPC Built Transfer Case EFI Live Comp Cam and Valvetrain Snow Performance Methanol Injection 35" Toyo Open Country Mud Terrain on 18" Ion Alloy 179's Headman Long Tube Headers and True Dual Exhaust FASS 150gph Titanium Series Pump AirAid Cold Air Intake with K&N Dry Filter & AirAid PowerAid Throttle Body Spacer 2" Suspension Lift 33x12.50r15 Tires PPE Tuner until i tune it with my EFI Live Pacesetter Long Tube Headers with Cats Gone True Dual Exhaust FlowPro 3.73 Gears Yukon Grizzly Locker with Mag-Hytec Cover & Traction Bars NGK Iridium Tips & MSD Ignition Plug Wires Baja Spare Tire Holder Leveling kit & 34.5" Nitto Grapplers 18" XD Rims Innovate LC-1 Wideband o2 Sensor x2 HID's all around LED taillights and 3rd brake light BDS Dual Steering Stabilizers Pioneer Double-DIN Touchscreen Navigation with Two 10" Subs under rear seat Electric Fan Autometer Pressure, Boost, and Pyro Gauges 4.56 Gears AFE Stage 2 Intake
05-20-2010, 03:40 PM #2
EasyOuts work real well depending on the size of the bolts. Me and my buddy have used them to remove broke spark plugs and broke real differential bolts. So they work pretty good when used right.1995 Silverado,Z71, 3-inch lift,2-inch leveling kit, SkyJacker Suspension, short ram-air intake, throttle body spacer, MSD ignition coil, straight pipes
05-20-2010, 03:54 PM #3
I'd try welding a nut to them if you can. The heat from welding might help to break it loose too.
If you can slide the entire manifold off right over the broken bolt that will give you a lot more bolt to weld on also.
05-20-2010, 05:19 PM #4
Best bet is taking the head off. They make a reverse drill bit, It cuts in the losen direction, They work good sometimes once you get into it they with start to back out.95 tahoe 2dr 4x4 200,000+ miles
05-20-2010, 06:05 PM #5
If you have the ability/facility to weld a nut on, that's the ticket. The extreme/rapid heating will usually break the corrosion bond, and you have a fresh nut to grab.When you hear hoofbeats, look for horses not zebras.
05-20-2010, 11:53 PM #6
That's what the plan was, just making sure you guys thought that was a good idea, only thing i'm concerned about is trying to weld in that spot. And not to burn anything. Oh well, wrap it in old rags and give'r ****.
By ippielb in forum The Coffee Shop ~ Chit ChatReplies: 6Last Post: 05-27-2010, 01:30 AM
By bucknasty in forum General Chevy & GM Tech QuestionsReplies: 2Last Post: 11-15-2009, 06:15 PM
By sc99z71 in forum Lifted & Offroad SuspensionReplies: 2Last Post: 10-14-2009, 10:39 AM
By redneckarmyMP in forum Chevy Silverado Forum (GMC Sierra)Replies: 2Last Post: 05-29-2009, 05:46 PM
By TrailLeadr in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 8Last Post: 03-23-2007, 11:11 PM