Results 1 to 4 of 4
Thread: New Intake Manifold Install
06-26-2010, 11:15 PM #1
New Intake Manifold Install
Getting ready to install a new Holley projection intake on my 5.7L suburban this weekend.
Need to know if their is anything special i need to know about?
Has anybody used this intake before and did you like it or remove it.
thanks in advance
D44/14BFF w/Disc conv - Yukon 4:88's - Yukon Grizzly Lockers F/R -13" lift - DIY4x Shackle Flip - 37 ATZ on 18 MT Classics - Doug Thorley headers - Magnaflow - Holley Pro Jection Intake - Ultimate TBI mods - Hydroboost Brake Conversion - Hysteer-X Over Conversion.
(Coming up - Fuel Injected 383 Stroker - Divorced NP205 - D60 - 40" tires)
06-27-2010, 01:16 AM #2
- Join Date
- Feb 2008
- Cloquet, Minnesota, United States
- Blog Entries
I havent heard of it to be honest.. I guess just make sure you get the gaskets in right.. But for sure let us know if you end up with a change in power.. and are you running a TBI still or a carb???Mike
1997 Chevy S-10 Blazer 4X4 with 330K miles and counting (Hunting rig).
2009 Saturn Aura XE (wifes car)
2011 F-150 Crew 4X4
"Hold it to the floor till you see God.... Then Brake!!!!"
06-27-2010, 11:38 AM #3
Nope, its all pretty simple, just drain fluid out of your rad, so you don't dump it all on yourself and over your engine. Just take your time, when you get your old intake manifold off, immediately put something in the intake holes, you can use a crumpled up piece of paper towel, or CLEAN rags. Then just clean up any grime and the old gasket. Then follow the instructions to install the gaskets the right way. And then just go in reverse from when you took the intake manifold off.
2002 Chevrolet Silverado 1500 z71 1985 Chevrolet Silverado k10 2006 Chevrolet Silverado 2500hd 6.6l LLY Duramax 6.5" BDS Suspension Lift Key'd to 9" Edelbrock Carb & Polished Intake Manifold & Valve Covers NAPC Race Transmission & NAPC Built Transfer Case EFI Live Comp Cam and Valvetrain Snow Performance Methanol Injection 35" Toyo Open Country Mud Terrain on 18" Ion Alloy 179's Headman Long Tube Headers and True Dual Exhaust FASS 150gph Titanium Series Pump AirAid Cold Air Intake with K&N Dry Filter & AirAid PowerAid Throttle Body Spacer 2" Suspension Lift 33x12.50r15 Tires PPE Tuner until i tune it with my EFI Live Pacesetter Long Tube Headers with Cats Gone True Dual Exhaust FlowPro 3.73 Gears Yukon Grizzly Locker with Mag-Hytec Cover & Traction Bars NGK Iridium Tips & MSD Ignition Plug Wires Baja Spare Tire Holder Leveling kit & 34.5" Nitto Grapplers 18" XD Rims Innovate LC-1 Wideband o2 Sensor x2 HID's all around LED taillights and 3rd brake light BDS Dual Steering Stabilizers Pioneer Double-DIN Touchscreen Navigation with Two 10" Subs under rear seat Electric Fan Autometer Pressure, Boost, and Pyro Gauges 4.56 Gears AFE Stage 2 Intake
06-27-2010, 01:16 PM #4
staying with the TBI. i have done a couple of mods to it thou.
---------- Post added at 01:16 PM ---------- Previous post was at 01:15 PM ----------
thanks guys, i will let you know how it turns out.
By mikemax in forum GM PowertrainReplies: 4Last Post: 03-19-2010, 01:30 PM
By Shmeag in forum Performance & FuelReplies: 13Last Post: 02-12-2010, 02:22 PM
By Blazedhertrails in forum Chevy Trailblazer Forum (GMC Envoy)Replies: 4Last Post: 07-20-2009, 09:23 AM
By 81monster in forum Performance & FuelReplies: 1Last Post: 04-03-2009, 12:35 PM
By Cleatus82 in forum General Chevy & GM Tech QuestionsReplies: 1Last Post: 06-12-2008, 11:05 PM