Results 1 to 5 of 5
Thread: Driver Side Window Problem
05-03-2007, 09:23 PM #1
Driver Side Window Problem
my power window won't slide down. one on the passanger side does fine. when pressed down, switch starts making clicking noise, like as if a relay is going on-off. i removed the switch, cleaned contacts, lubed contacts - same result. this happened about a week ago, then problem went away all by itself. now it's back.
i can replace anything in it by myself, just need to know what to. sounds like motor gone bad, or maybe lose contact and relay just kicks back.
please, help with advice.
2000 silverado 1500 ext. cab.
PS: on the same token, does anyone know how to unstuck a stuck window? i went through car repair manual, it says that window motor has a safety feature preventing it from burning if it takes too much effor to move the window. which that window was going down easy but squeeky slowly up before. now it starts sounding like the click is coming from that safety switch. looks like door to be disassembled over the weekend and guides cleaned and lubed.
Last edited by ukrkoz; 05-03-2007 at 11:26 PM.
05-05-2007, 10:47 PM #2
Few Days Later
ok, it fixed itself next day. second time it happens. so, i took the doorpanel off today, cleaned and lubed window guides, ran window up/down few times.
sounds like motor will go off on me soon, as after 4-5 runs, it slows down and whines louder.
i scoped few more forums looking for the same problem solutions. appears driver side door is notorious about this. someone mentioned routinely torn motor wires, indeed, for whatever reason they were factory installed wrapped around thick wand of wires in the door, and i could see that insulation already was taking some damage from the door panel. so i fixed that. some owners, quite proudly, mentioned that they had 2 motors go bad in one year.
well, so far so good. someone needs to come up with a hybrid window lowering mechanism - if motor goes bad or switch or something, then have crank available.
05-05-2007, 11:16 PM #3
Welcome Ukrkoz, Sorry I didn't see your post earlier. Looks like you found it mostly. The chafing area where wire is pinching I use silicone grease to keep the wires safe. So repair wire/wires then (use solder and heat shrink tubes) tape up lube wires. Then I would say your just holding off the inevitable (replace P/W motor) It'll fail on a rainy day and you'll be trapped with the damn window down
Good luck, lets us know how you make out.
2007 Ford E250(Work van) (Ya, Ya, shut up!)
1996 GMC Sierra SLE 1500 5.7L/4L60E
05-07-2007, 06:10 PM #4
thanks you, larry the cableguy . i think i got it, it'll run for some time.
what i do not understand, is why i , person with 11 years of university education, very frugal and practical, would put my 28mpg CR-V, one that does not even know what the word "repairs" means after 100 000 miles on ticker, into garage, and drive that clunking, jerking, gas guzzling hog, that already cost me a transmission switch, this hassle, lubricating slip yoke, kicks like an old mule at low speeds, clunks in that intermittant driveshaft, and all that only at 60K? BECAUSE I ENJOY IT?
hey, what can i say. i guess, i'm as bad as any other redneck in a row. love the damn vehicle. probably a "keep me busy over the weekend" car, but hell no, i ain't going into nothing smaller from now on. besides, has more features in it than my wifes RX300.
05-07-2007, 06:17 PM #5
Thats the spirit get in there and muck about till ya figure it out. Hey I think I just made a poem. It is fun...but you can sure waste a day away. Mind the "Honey-Do list" though or you'll get yelled at.
By mktylor in forum Chevy Express Forum (GMC Savana)Replies: 1Last Post: 02-17-2010, 12:30 PM
By bassalive in forum General Chevy & GM Tech QuestionsReplies: 1Last Post: 09-01-2009, 08:31 AM
By MarlboroMan in forum Chevy Silverado Forum (GMC Sierra)Replies: 5Last Post: 06-04-2009, 04:29 AM
By surferboyyy in forum Chevy Colorado Forum (GMC Canyon)Replies: 0Last Post: 02-27-2007, 09:19 PM
By tcmerrick in forum Chevy Trailblazer Forum (GMC Envoy)Replies: 0Last Post: 12-07-2005, 10:34 PM