Results 1 to 10 of 20
08-16-2010, 10:33 PM #1
AC pressure after changing compressor ????????
Hi, i need to know how much pressure i need to fill in my 1996 Suburban !
It has rear AC aswell.
Any help would be very much apriciated .
PS, maybe somebody knows how much goes in a 88 Camaro also ???? LOL ( wifes car )
1996 Suburban K3500 SLT DUALLY
1988 Camaro RS 383 stroker LT1
1992 32' Aero-tek Race Boat, 600 CI BBC
WE CAN STICK A DIESEL IN ANYTHING
SPECIALIZED IN CUSTOM CONVERSIONS OF ANY KIND
08-16-2010, 11:21 PM #2
Did you add in oil to the COmpressor as well??
And put a vaccuum on the system??
If those are in place, it should take about 3 - 4 cans easily.
Do it with manifold guages, then you can watch the pressure build, and stop when it gets to 40 - 45 Low side.
I don't believe the fact of having rear air makes a difference, but I could be very wrong on that assumption.
---------- Post added at 11:21 PM ---------- Previous post was at 11:19 PM ----------
If you put on a new compressor and therefore the system is empty.
If not done as well, change out the accumulator and the orifice tube.
08-17-2010, 08:50 AM #3Mike
1997 Chevy S-10 Blazer 4X4 with 330K miles and counting (Hunting rig).
2009 Saturn Aura XE (wifes car)
2011 F-150 Crew 4X4
"Hold it to the floor till you see God.... Then Brake!!!!"
08-17-2010, 01:56 PM #4
Thank u all, but i have a 30# can and REAL gauges to fill the AC , also yes...oil in and vaccum done..-28 !!!!
but @ 45 PSI my compressor wont even turn on.....at 65 it will work fine...??????????????????????????mmmmhhh
08-17-2010, 01:59 PM #5
Seems that your high pressure switch has had it. And you are at 45PSI on the low side with the compressor running? not to be stupid just confused because i know that real guages allow for more accuracy. but you should have a 3lb system. So i would have installed 3lbs and gone from there. but that is why i am confused because your low side should be 45lb with the compressor engaged. If the compressor is off then it isnt sucking on the low pressure site to lower the system pressure.
08-17-2010, 02:02 PM #6
When the compressor is running it reads 55-60 PSI on low and about 250 on high !!!!after turning it off, it reads 75 on both !!! mmmmmhhhhh I'M LOST ..LOL
Tomorrow i will bring it to an AC shop and let them figure this SH[T out..hahaha
98 degree down here today ....sweting my a$$ off.
08-17-2010, 02:06 PM #7
Hmm sorry man. Confussed is right.. Is it cold at least?? And do you know how many lbs of R134a you put in? But it really seems like you have a bad high pressure switch. And or else a low pressure switch depending on which you are jumping to get the compressor to run...
08-17-2010, 02:09 PM #8
Not jumping any...just filling it untill ~ 60 and then it comes on !!!!! and yes its cold but i still have a small leak in my line..lol thats why i filled it new ( i thought i fixed the leak ) THOUGHT !!!!!! is the main word....lol I found out that J&B weld is not strong enough on aluminum AC pipes...hehehe
08-17-2010, 02:21 PM #9
WEll thanks for the insight.. and that may be some of your issue is a the leak may not be allowing the proper pressure at the actual switches.. But i would lean twards a bad low pressur switch then. Since it is supposed to tell the compressor to kick on when you obviously have enough pressure.
08-17-2010, 04:42 PM #10
By ruebeng28 in forum General Chevy & GM Tech QuestionsReplies: 1Last Post: 10-19-2009, 11:00 PM
By 99 Z71 in forum General Chevy & GM Tech QuestionsReplies: 0Last Post: 08-17-2009, 01:34 PM
By bUCKOLA in forum Chevy Silverado Forum (GMC Sierra)Replies: 12Last Post: 07-22-2009, 05:47 PM
By thePhilster in forum General ClassifiedsReplies: 1Last Post: 06-24-2008, 08:32 AM
By sbw9056 in forum General ClassifiedsReplies: 1Last Post: 01-29-2008, 11:10 PM