Results 1 to 7 of 7
10-02-2010, 12:52 AM #1
- Join Date
- Oct 2010
How do you take out the tail gate bow tie on a 2010 silverado??
have two new bow ties on the way. know how to get the front one out just need to figure out the easiest way to get the tailgate bow tie out?? thanks
10-02-2010, 01:15 AM #2
- Join Date
- Sep 2010
- Far West, Oregon USA,
- Blog Entries
Welcome to the GM Truck Club. Don't want you to think we're all ignoring you 10Silverado3, but your's is the first que. I've seen about this. I don't know, but somebody will be along who has knowledge.
10-02-2010, 06:21 AM #3
Take a thin piece of fishing line, slip it behind the emblem and pull it back and forth with both hands. You need to cut the double stick tape behind it, that's how they're held on. Clean up with goo gone(goof off) of better yet get a 3M rubber eraser wheel attachment for your drill.
4WD/4.88s/TrueTrac/EFI Live | Rancho 4" SL | 3" BL| 20" Ballistic Jesters | 35" Toyos
Fabricated One-Off Prerunner Lightbar, Bed Tire Mount and Dual Shock Hoops w/ FOAs
10-03-2010, 01:20 AM #4
you can use a hair dryer to heat up the adhesive and make it easier to work with. Recommend you do it on a relatively warm day, cuz removing emblems/ moldings when its cold out is a royal PIA haha.04 ECSB Custom silver & grey, Soft 8's, BFG KO's, ReadyLift Leveling Kit, Hellwig front sway bar, K&N filter, DeeZee EZ-Down, Rhino liner, Alpine CDE103BT, Rockford 6.5's, 12" V.A.T. Hammer Pro in a Subthump box, Alpine PowerPack amp, Hifonics amp, BackRack w/ 55w 5000k HID KC Daylighters, KC light bar with 4 KC Slimlites, UWS toolbox, Shaved Antenna mod, Black Bowtie, LED backup, license plate, dome lights & 3rd brake light
10-03-2010, 07:32 AM #5
Hair dryer,fishing line,and goo gone[/SIGPIC]2009 Chevy Silverado LT 1500 EXT CAB 4X4 Vortec 4.8L SFI,K&N air filter,Weathertech Floor Liners ,Weathertech Stone/Bug Deflector, Line X Spray On Bedliner, TruXport Rollup Tonneau Cover, Molded Mudguards, Viper 5701 LE 2 way Security Alarm/Remote Starter, Xm Satelite Radio,BILSTEIN 5100 rear shocks,BILSTEIN 5100 front levelling shocks,READYLIFT 2" rear lift blocks,Goodyear Wrangler Territorys -265/70R 17"
10-03-2010, 11:37 AM #6
Im glad someone had the answer to this. cause i was worried that there would be boles behind it. also a thanks
10-06-2010, 08:22 AM #7
No holes, just glue , I painted mine black last week , and the temperature was in the 90's , so the glue stayed very sticky. I was able to stick it back to the original glue after I painted it! Acourse it was sitting in the sun the entire time , and I pull on it regulary to check and it's still stuck like it came from the factory! Good luck
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 04-01-2010, 09:40 AM
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 03-06-2010, 04:20 PM
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 10-24-2009, 02:50 PM
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 10-24-2009, 12:51 AM
By Steve in forum Chevy Parts eBayReplies: 0Last Post: 08-09-2009, 02:30 PM
Tags for this Thread