GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 6 of 6
  1. #1

    Default 07 Chevy 2500hd leveling

    Whats up. I am thinking about leveling my 07chevy 2500hd. Would I be able to do it myself. I have googled it and found some leveling keys. Is there anything that I need to look for. Is it a job that I can do in my drive way. Is there anything that i need to know or look for. Thanks

  2. #2
    Legend


    mfleetwood's Avatar
    Join Date
    Jul 2010
    Location
    Denver, CO
    Posts
    7,213
    Blog Entries
    1

    Default

    Welcome to the Club! Unfortunately, I am not familiar with how the torsion key lift/level works, but here is link to a thread that should get you started in answering this and many other questions. If you cannot find what you are looking for on this thread, scroll to the bottom and you will see on the left hand side some other similar threads that will have additional information.


    http://www.gmtruckclub.com/forum/sho...eling-kit-page


    Mike (Denver, CO) - 2008 Sierra 1500 Z71 SLE 5.3L 4WD

    SUSPENSION: Rancho 4" Suspension Lift; Rancho RS9000XL Shocks; Rancho Skid Plates; Rancho MyRide Wireless Shock Controller;
    TIRES:
    BFG All Terrain KO 315/70/17
    DRIVE TRAIN: 4.56 Gears; Detroit TrueTrac Differential; True Cool 40k Transmission Cooler
    PERFORMANCE: DiableSport Predator Tuner; Custom Tuned by Diablew; Magnaflow Exhaust; AFE Cold Air Intake
    ELECTRONICS: Kenwood DNX6180 Touchscreen; Subthump box w/10" Kicker; Driver Information Center (DIC); Rear View Camera
    ACCESSORIES: Westin Brush/Grill Gaurd; Westin Nerf Bars; Truxedo Tonneau; 20% Tint; Tow Mirrors w/Heat & Signals

  3. #3

    Default

    Welcome to the club. You will need a torson bar key compresion tool. You can rent these. DON'T buy cheap leveling keys. Also you will need longer shocks or shock extensions. Check out Offroadunlimited.com (ORU) 2500's leveling kits. If you truck has miles on it than now would be a good time to replace the front shocks with longer ones. ORU has a kit with longer Bilstein shocks and forged keys, a great kit.

  4. #4
    Legend Bigbomber's Avatar
    Join Date
    Feb 2010
    Location
    Winnipeg,Manitoba,Canada
    Posts
    5,089

    Default

    Welcome to the site!
    [/SIGPIC]2009 Chevy Silverado LT 1500 EXT CAB 4X4 Vortec 4.8L SFI,K&N air filter,Weathertech Floor Liners ,Weathertech Stone/Bug Deflector, Line X Spray On Bedliner, TruXport Rollup Tonneau Cover, Molded Mudguards, Viper 5701 LE 2 way Security Alarm/Remote Starter, Xm Satelite Radio,BILSTEIN 5100 rear shocks,BILSTEIN 5100 front levelling shocks,READYLIFT 2" rear lift blocks,Goodyear Wrangler Territorys -265/70R 17"

  5. #5
    Legend
    murdog94's Avatar
    Join Date
    Feb 2008
    Location
    Cloquet, Minnesota, United States
    Posts
    8,198
    Blog Entries
    12

    Default

    Welcome aboard!
    Mike

    Currently

    1997 Chevy S-10 Blazer 4X4 with 330K miles and counting (Hunting rig).

    2009 Saturn Aura XE (wifes car)

    2011 F-150 Crew 4X4

    "Hold it to the floor till you see God.... Then Brake!!!!"

  6. #6

    Default

    WEll you can if you have the right tools. you will need a tortion bar tool. and dont get a cheap one! its basically a giant really strong C clamp with little nipples that grabe the key and the crossmember properly so there is no slippidge.

    just jack up the front end, take the tortion bolts all the way out, then put yoru tortion tool on and tighten itup until you can slide out the little plat that holds the tortion bolt. once its out then let out the tortion tool. (do it to the other side now too). then you will need a hammer and something to hit on the back of the key with. I used a solid pipe. before hammering heat the key up to try and losen it (becareful on the drivers side there is a gas line in the area). put your rod or tip of the air hammer in the hole on the back side of the trotion crossmember and just hit away until the bar slides forward. This may take a while.once it goes all the way forward the Key can drop out the bottom so watch your face! oncve it does slide in the new once and made sure you put the tortion bar back in correctly (if your nervous about it mark the bottom side of it so you know). Now use your tortion tool and push that key back up there and slide in the tortion bolt bridge. then let out the tortion tool and then tighten in your tortion bolt. make sure and do it evenly. and when making adjustments do it with the front end off the ground.

    Let me know if you want the Rough country leveling kit for your truck

Similar Threads

  1. Is the 10' Chevy 2500HD 6.0 a workhorse?
    By liberate in forum Chevy Silverado Forum (GMC Sierra)
    Replies: 10
    Last Post: 08-25-2010, 06:34 AM
  2. Replies: 0
    Last Post: 05-12-2010, 09:30 AM
  3. Replies: 0
    Last Post: 04-11-2010, 04:12 AM
  4. Replies: 0
    Last Post: 12-26-2009, 07:20 PM
  5. I just did the ready lift leveling kit on my 06 2500HD
    By chevymon in forum Lifted & Offroad Suspension
    Replies: 3
    Last Post: 04-24-2009, 02:50 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •