Results 1 to 3 of 3
03-29-2013, 11:12 PM #1
- Join Date
- Jan 2009
- Norwalk, Ohio
- Blog Entries
2008 HHR SS wheel hub/bearing replacement (pics)
Driving home from work last week in the pouring rain, I hit a HUGE pothole and hit the front passenger side wheel hard. One week later I have a roaring noise coming from the right front wheel, today we took care of the problem.
We used the front part of the unibody to jack the HHR up from, the pad was right underneath the engine mount as well. It was actually very easy to remove the wheel hub.
2 bolts for the caliper, 2 bolts brake pad holder, 3 bolts for spindle, knock the upper ball joint out after removing nut. remove rotor, you don't have to remove the lower ball joint as the spindle will articulate out of the way far enough to get to the bolts. 3 bolts for the wheel hub assembly.
The rear seal was completely gone, which caused water to get into the bearing and some of the cone bearings were actually egged. Went to Advanced Auto which had about 20 different choices, I had him bring out ACDelco $376.00, and MOOG $189.00. Acdelco made in Mexico, MOOG made in China.......I went with Moog, 3 year warranty I couldn't justify $400 for a hub sorry.
The unit came with new ABS ring and connector, very nice quality. We also greased all CV joints, and balljoints which were basically dry from previous owner.
As far as grease goes, I stumbled across some awesome stuff at Walmart about 2 years ago. It's called green grease, It's a marine grade grease and I mean that stuff is awesome, nothing affects it either. Heat, oil, brake fluid, gas, water, $5.00 for a tube, and it lasts forever. VERY MESSY!!
We also checked the CV shafts, and there was no play whatsoever. Took it for a test drive once it was finished, and It was as quiet as can be. Took us about 2 1/2 hours of working time, It was my first FWD experience so It was slow ha ha!!
2004 Chevy Colorado
LS1 5.7 swap/TBSS rear axle swap
03-30-2013, 08:44 AM #2
- Join Date
- Apr 2010
- Piermont,NY, back in Northern NJ now, But may be in IL soon....
We want to see your hands dirty.... j/k...08 Z71 Avalanche Mods to date: K&N CAI,Hellwig Swaybars and End Links, Corsa Sport Exhaust, Superchips Programer,IPCW LOF & 3rd brake light and tails, AMI Gas door,Show Hooks and Door locks, Enkei Wheels, with Pirelli tires, StreetScene Bowties, Grant Steering wheel,Muth signal mirrors,SSBC Big Brake kit,Huskyliner Mug gards,Floor mats and Hood shield, McGard Lug nuts and locks, Bedrug, Cervini's Ram Air hood,35watt HID Fog lights, Sylvania bulbs all around ZXE's Highs and Lows, WhiteNight Back up lights,Sirius and HD Radio, SnugTop sitting on deck now Got a Softopper on now,Tempress Boat Hatches.... New Bilstein shocks are on... New Mods coming soon..... X
03-31-2013, 10:25 AM #3
Looks just like my '08 HHR SS, so I figure that I'll be getting to this job someday.
I see that the shock tower was unbolted from the lower suspension assy. When jacking up the frame and letting the wheel hang, is the spring fully decompressed at this point?
HHR SS_________________The Heritage Hot Rod
By vanhoand in forum Chevy Silverado Forum (GMC Sierra)Replies: 3Last Post: 08-31-2012, 12:21 PM
By Enkeiavalanche in forum PA - Pennsylvania Chevy Truck ClubReplies: 8Last Post: 07-17-2012, 09:09 PM
By ippielb in forum Maintenance & UpkeepReplies: 0Last Post: 07-06-2012, 09:01 PM
By Niekamp-Alaska in forum Chevy C/K Truck ForumReplies: 1Last Post: 01-23-2012, 07:46 PM
By mike04rr in forum How-to GuidesReplies: 14Last Post: 10-29-2011, 06:06 PM
Tags for this Thread