Results 1 to 10 of 12
07-22-2011, 08:06 AM #1
- Join Date
- Jul 2011
upper and lower ball joint replacement 1997 chevy k1500
I need to replace the upper and lower ball joints for my chevy 1500 4x4. The problem is, I don't have the money to get it done at a shop, and frankly I have no clue how to replace them. Could anyone give me a step-by-step guide? If it makes a difference, it is the front passenger side. Or do you think it would be easier to replace the control arms? If you feel that is the case, can you tell me how to do that then? Thanks!
Last edited by karroe; 07-22-2011 at 08:23 AM.
07-22-2011, 05:36 PM #2
Welcome to the club. The factory balljoints are riveted on. Not a big deal. I like to cut a "X" with a die grinder in the rivet and them chisel off with a air chisel. If you don't have a air chisel then you can use a hammer and chisel, just takes longer and harder. You can also use just a grinder to grind off the rivet. Everyone has there favorite way. The new b/joints just bolt-in.:cool:
2005 Chevy Silverado Z71 Crew Cab
6" Skyjacker lift w/Edlebrock dual front remote resoviour shocks, single rear remote. Rancho skid-plate.
17" x 9" M/T Classic Lock Wheels, 35" BFG A/T or M/T tires
4.10 PercisionGears w/factory locker, T/A Performance rear-end cover
Banks CAI intake, ported throttlebody, JBA coated headers, over-sized Magnaflow cats, Magnaflow cat back exhaust, Diablo tuned
B&M aluminum deep transmission pan
Warn brush guard w/Warn 9.5 XP winch, PIAA bulbs, Line-X bedliner, AWS Black tool chest, Extang tonneau cover
Weather Tech floor mats
Cover-Craft seat covers
Dash mat cover
Formula One window tint
One black Lab in rear seat.
07-23-2011, 05:03 AM #3
- Join Date
- Sep 2010
- Far West, Oregon USA,
- Blog Entries
When it comes to getting the ball joint tapers out of the steering knuckles, loosen the nuts, back them off a couple turns but don't take all the way off. Then hit the knucke where the BJ goes through it with the largest hammer you can accurately swing in there. This will shock them to release. The other option is a pickle fork but if you've never done this before you aren't likely to have one so go with the hammer method. There's really no benefit to replacing the entire control arms unless yours are bent, or rusted really bad. The amount of work is about the same, & you still have to break the ball joint tapers loose from the steering knuckles.1988 Chevy C-3500 2wd (no pic)
350 c.i. 5.7 L Stock Block, 4 Bolt Mains
L-31 Vortec Heads, Edelbrock Cam & Intake,
Holley 650, Flowtech Headers, Magnaflow exh.
Jet Trans 700R4, B&M Ratchet, 4:10 gears,
3" susp. lift kit "shadetree"
No rev limiter, No speed limiter lol
07-28-2011, 02:32 PM #4
Guess I'll cover the lower ball joints. The lower ball joints are going to be a pain, a really big pain. First, you need to support the lower control arm with a jack stand, and put the weight of the truck on the jack stand, so find the flattest spot on the lower control arm, and then lower the truck onto the jack stand at that spot.
Then you loosen the bolt on the steering knuckle, just a tad, then you smack the side of the nuckle like Stephen said with the upper ball joints. When it comes loose, move the steering knuckle out of the way. Now, you're going to need a ball joint press for this, there's really no other way to do this if you don't have one. You can either get a really big hammer, and smash the lower ball joint out of the control arm, or you can press it out with a ball joint press.
Pressing them back in is the hardest part by far, it always gives me problems, especially if your press is cheap, and it doesn't press straight. Get you're ball joint press, find the fittings that will fit on the outer edge of the ball joints base, not the inner plate, the outside rim, and find a fitting that will fit over the top of the control arm, that also allows room for the ball joint to come up through, and just press it is AS STRAIGHT AS POSSIBLE! If you're off just by a little bit, then you'll have to go through the painful process of smacking the control arm, while pressing at the same time, in a attempt to straighten it and get it to sit flush with the control arm.
I recommend you have a shop do the lowers if you've never done it yourself, it's more trouble than it's worth if you've never done them on these trucks before.1994 Chevy Silverado 1500 Ext Cab 350 cuin TBI in dark Chevy blue
Original engine and tranny
wrecked twice stolen once
Diamond Plate bed rails
Original Alloy wheels
Original fancy smancy cup holder
Original plastic bed liner
K&N Cone Air Intake
Dual MagnaFlow exhaust(not true dual) with chrome tips
MSD Street Fire Performance Ignition coil
12-26-2011, 04:24 PM #5
- Join Date
- Dec 2004
- Arlington, Texas, United States
- Blog Entries
10 Chevy Traverse LT AWD
02 Chevy Trailblazer LS (110K+ miles - loaded except for 4WD - WRECKED!)
99 Chevy Cavalier LS (105K+ miles - commuter car)
78 Chevy Suburban Silverado (454, 3/4 ton)
62 GMC 3/4 ton Pickup (350 police interceptor)
Remember: Search Before Posting | Fill out Your Profile & Signature
* I've been saying for years that I was going to change my username, and I finally did.
02-11-2012, 08:58 AM #6
- Join Date
- Dec 2011
This last post is veryyyy accurate....if you have no idea how, might be better to pay and have it done...if not and you wanna tackle it yourself, GET a ball joint press, they sell em at Northern Tool pretty reasonable with adapters to fit domestic cars n trucks........top ones are easy......and to add to the bottom ones, you have to be careful and put the weight of the truck on that A-arm as stated above, because it is DANGEROUS, you DO NOT want the coil spring to come out, it is under extreme pressure and can cause fatal injuries if it does.........also, get you a Haynes or Chilton manual, they have step by step instructions...
02-13-2012, 10:42 AM #7
[QUOTE=59diesel;440223]This last post is veryyyy accurate....if you have no idea how, might be better to pay and have it done...if not and you wanna tackle it yourself, GET a ball joint press, they sell em at Northern Tool pretty reasonable with adapters to fit domestic cars n trucks........top ones are easy......and to add to the bottom ones, you have to be careful and put the weight of the truck on that A-arm as stated above, because it is DANGEROUS, you DO NOT want the coil spring to come out, it is under extreme pressure and can cause fatal injuries if it does.
I don't think that that year has a coil spring. They are IFS front ends. I could be wrong. My 95' k1500 has no coil springs. The lowers are not that bad to do. I do them A LOT in my 95, the 38" tires eat them at least once a year. It takes me about an hour per side now. I just rent the press from Autozone for free. I have seen some with a circlip on them, so make sure you clean up the old ones real good before you attempt to take it apart, so you can see if there is one there. Nothing like cranking on a press and finding out after an hour that there is a clip holding the ball joint in. You do have to support the lower control arm, the load from the torsion bar pushes it down with a lot of force.
1995 Silverado 4x4
6" BDS Suspension Lift-3" Body Lift-Add A Leaf in rear -Trailmaster SSV Shocks-Duel Steering Stabilizer Kit -AirAid Cold air intake-
4.56 Gears with Detroit Auburn Locker-Pro-Comp Traction Bars with duel shocks-Aluminum Skid Plate Kit-38.5" x 16.5" Mickey Thompson Baja Claws-Constant Dropping fuel gauge
2005 Yukon XL Jet Power Programmer, Bilstein Shocks, Bilstein rear springs, Helwig Anti-sway bars, EGR Window Visors, EGR Hood Shield, Denali Headlights, Headlight harness upgrade, GE NightHawk Bulbs, White Night Rear lighting system, Russell Braided SS brake lines, PowerStop Brake pads, PowerStop cross drilled and Slotted Rotors, http://www.gmtruckclub.com/forum/sho...5-GMC-Yukon-XL
2002 Silverado ext cab 2wd (Sold)
2003 Yukon XL (Totaled)
02-13-2012, 03:34 PM #8Remember that if you're not part of the solution, then you're part of the problem!
02-16-2012, 02:19 PM #9
I just went outside and looked at me 1995 silverado 4x4. The uppers were riveted in from the factory. I had to remove the rivets and the new ball joints came with bolts. The lowers are pressed in. So Revredneck you may be right! some chevys may have come that way. I am looking at something completely different then what you have posted. on My 2002 silverado 2 wheel drive the lowers are riveted in. I drilled the rivets out with a carbide drill bit.
03-01-2012, 09:16 AM #10
depends on year, my 1993 K1500 has riveted in on top and bottom and you are right, you can also compress the spring and take the whole arm to a shop and have them press the ball joint in if you are hard out for money most of them will press it real quick for next to nothing. Oh and word to the wise, buy a good ball joint its worth the extra to get a nice part, I still go to the Chevrolet dealer and buy my ball joints and other parts where failure can be dangerous. As an A.S.E. mechanic I can preach all day on the importance of factory parts
1993 K1500 Suburban
2008 Subaru Outback Sport
1987 Chevrolet R10 Silverado (Sold)
2012 Hyundai Santa Fe
By bleebs in forum Lifted & Offroad SuspensionReplies: 7Last: 05-02-2011, 03:48 PM
By ChevyFan in forum Chevy Parts eBayReplies: 0Last: 03-25-2010, 06:00 PM
By 97suburban in forum Lifted & Offroad SuspensionReplies: 0Last: 05-31-2009, 07:58 AM
By GlitchMobile in forum How-to GuidesReplies: 2Last: 11-13-2008, 03:32 PM
By maury in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 4Last: 05-02-2008, 09:23 AM
Tags for this Thread