GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 10 of 10
  1. #1

    Default '88 Blazer sputters and misses under load

    I have a 88 blazer full size w/ 350 and throttle body. The truck sputters and misses under load but only after being driven for at least 5 - 10 minutes. It starts fine and always idles fine. Doesn't miss revving in park but will do it in drive and brake applied. There are no codes.

    Here's what I have done so far...

    Cap and rotor
    fuel filter
    Clean and gap plugs and inspect for damage. replaced one and one was quite oil-fouled.
    Replaced one plug wire that had got hot and swelled.
    checked for vacuum leaks
    Replaced muffler [no catalytic converter]
    Fixed pos battery cable that had contacted exhaust and was 1/2 eaten thru and shorting-- giving me an intermittent check engine light. That has stopped.
    Timing
    Checked EGR- idle decreases when pushed, moves when revved

    I have read other posts on this topic and fuel pressure test is recommended. I have a gauge but there is nowhere to hook it up on fuel injection. It only has the tank mounted fuel pump and the manual says you can't work on it or check it and need special tools. How can I get an idea if this is possibly the problem.

    I also still need to check for play in the dist. gear.

    I'm new here and if anyone has any advice it would be greatly appreciated. Thanks!
    Last edited by flatearthling; 07-31-2011 at 02:56 PM.

  2. #2

    Default

    I just removed the O2 sensor and it is really dirty. Manual says no solvents so how to clean?

    This would seem to be a possibility for my problem as it functions on a loop until it reaches 600 degrees.


    EDIT>>>> Replaced O2 sensor and still no help.
    Last edited by flatearthling; 07-31-2011 at 09:43 PM.

  3. #3

    Default

    New fuel pressure regulator and water temp gauge and still not fixed.

    I'm getting tired of throwing money at the problem. Remove and inspect the distributor is next I guess.

    Would be nice to get any response to my post. It would be greatly appreciated.

  4. #4

    Default

    how did you check for vacuum leaks? I recommend spraying carb spray around till you find one if there is any. it sounds like a vacuum leak.

    2003 Z71 Silverado LS
    Access roll up cover
    Bed Rails
    Billet Grill insert
    Bed Rug
    CB with PA system
    Waiting to be installed
    Two 8in RF HX2 punch( would have 12s but they got stolen)

  5. #5

    Default

    When was the last time you removed the throttlebody and gave both top and bottom a good cleaning with a good throttlebody cleaner and a soft brush? Also take the IAC valve out of the t/body and give it a good cleaning also.

    ---------- Post added at 07:22 PM ---------- Previous post was at 07:21 PM ----------

    Even if this is not the problem it should be done if you haven't done it.
    :cool:

    2005 Chevy Silverado Z71 Crew Cab
    6" Skyjacker lift w/Edlebrock dual front remote resoviour shocks, single rear remote. Rancho skid-plate.
    17" x 9" M/T Classic Lock Wheels, 35" BFG A/T or M/T tires
    4.10 PercisionGears w/factory locker, T/A Performance rear-end cover
    Banks CAI intake, ported throttlebody, JBA coated headers, over-sized Magnaflow cats, Magnaflow cat back exhaust, Diablo tuned
    B&M aluminum deep transmission pan
    Warn brush guard w/Warn 9.5 XP winch, PIAA bulbs, Line-X bedliner, AWS Black tool chest, Extang tonneau cover
    Weather Tech floor mats
    Cover-Craft seat covers
    Dash mat cover
    Formula One window tint
    One black Lab in rear seat.
    :glasses:

  6. #6

    Default

    Well, I fixed my problem and have the truck tuned up and running fantastic. Turns out my problem was a little 3-way check valve in the vacuum hose that was broken. One of the first things I had checked was vacuum hoses and somehow had neglected to see the broken T fitting as it had fallen down behind the distributor. One side of fitting led to the back of the throttle return control and another led to a barb on the back of the intake manifold.The third hose went thru the firewall to ? [cruise control?] That line had another T w/ line to transmission? All of that was open because of the broken valve.

    Could have had it fixed if I'd been more thorough the first time. You live and learn.


    Any way, the truck is fixed and I wanted to post the results. I read a lot of threads about similar problems and most of those posts just end mid-problem with no final chapter. Didn't want this thread to go out like that. Some help there from previous posts and I like the way links come up for similar threads.

    I finally got some response to my posts from the regular members tho.....You must get an endless parade of new members who post the same vague questions over and over and then leave when their ride runs again and no thanks.

    Well, thanks for the help.

    I probably knew better than to double post as if I didn't know where the edit button was and the thread needed bumping.

    Actual recent pics of my truck:










    Which stripping package should I go with? I can't decide...

  7. #7

    Default

    Well, I fixed my problem and have the truck tuned up and running fantastic. Turns out my problem was a little 3-way check valve in the vacuum hose that was broken. One of the first things I had checked was vacuum hoses and somehow had neglected to see the broken T fitting as it had fallen down behind the distributor. One side of fitting led to the back of the throttle return control and another led to a barb on the back of the intake manifold.The third hose went thru the firewall to ? [cruise control?] That line had another T w/ line to transmission? All of that was open because of the broken valve.

    Could have had it fixed if I'd been more thorough the first time. You live and learn.


    Any way, the truck is fixed and I wanted to post the results. I read a lot of threads about similar problems and most of those posts just end mid-problem with no final chapter. Didn't want this thread to go out like that. Some help there from previous posts and I like the way links come up for similar threads.

    I finally got some response to my posts from the regular members tho.....You must get an endless parade of new members who post the same vague questions over and over and then leave when their ride runs again and no thanks.

    Well, thanks for the help.

    Z71-guy and Silver nailed it anyway.

    I probably knew better than to double post as if I didn't know where the edit button was and the thread needed bumping.

    Actual recent pics of my truck:













    Which stripping package should I go with? I can't decide...

  8. #8

    Default

    Well, I fixed my problem and have the truck tuned up and running fantastic. Turns out my problem was a little 3-way check valve in the vacuum hose that was broken. One of the first things I had checked was vacuum hoses and somehow had neglected to see the broken T fitting as it had fallen down behind the distributor. One side of fitting led to the back of the throttle return control and another led to a barb on the back of the intake manifold.The third hose went thru the firewall to ? [cruise control?] That line had another T w/ line to transmission? All of that was open because of the broken valve.

    Could have had it fixed if I'd been more thorough the first time. You live and learn.


    Any way, the truck is fixed and I wanted to post the results. I read a lot of threads about similar problems and most of those posts just end mid-problem with no final chapter. Didn't want this thread to go out like that. Some help there from previous posts and I like the way links come up for similar threads.

    I finally got some response to my posts from the regular members tho.....You must get an endless parade of new members who post the same vague questions over and over and then leave when their ride runs again and no thanks.

    Well, thanks for the help.

    Z71 and Silver had it nailed anyway.

    I probably knew better than to double post as if I didn't know where the edit button was and the thread needed bumping.

    Actual recent pics of my truck:













    Which stripping package should I go with? I can't decide...

  9. #9

    Default

    FlatEarthling, Have you looked into the Locking Torque Converter (assuming your Blazer is an auto, you didn't say) I have a f/s blazer that would cut out and sputter uphill (usually) with the engine at about 1600 RPM,it all cleared up when I forced a downshift to passing gear.. Boneyfingers

  10. #10

    Default

    Well, I fixed my problem and have the truck tuned up and running fantastic. Turns out my problem was a little 3-way check valve in the vacuum hose that was broken. One of the first things I had checked was vacuum hoses and somehow had neglected to see the broken T fitting as it had fallen down behind the distributor. One side of fitting led to the back of the throttle return control and another led to a barb on the back of the intake manifold.The third hose went thru the firewall to ? [cruise control?] That line had another T w/ line to transmission? All of that was open because of the broken valve.

    Could have had it fixed if I'd been more thorough the first time. You live and learn.


    Any way, the truck is fixed and I wanted to post the results. I read a lot of threads about similar problems and most of those posts just end mid-problem with no final chapter. Didn't want this thread to go out like that. Some help there from previous posts and I like the way links come up for similar threads.

    I finally got some response to my posts from the regular members tho.....You must get an endless parade of new members who post the same vague questions over and over and then leave when their ride runs again and no thanks.

    Well, thanks for the help.

    Z71 and Silver had it nailed anyway.

    I probably knew better than to double post as if I didn't know where the edit button was and the thread needed bumping.

    ---------- Post added at 02:12 AM ---------- Previous post was at 02:08 AM ----------

    Actual recent pics of my truck:








    Needed 5 posts to put up pics. I can't decide on the stripping package. Which is best?

Similar Threads

  1. Chevrolet : Blazer Blazer Blazer Military truck cucv M1009 4x4 6.2 diesel
    By ChevyFan in forum Chevy Trucks For Sale eBay
    Replies: 0
    Last: 02-28-2011, 07:50 PM
  2. 1996 Silverado Spits and Sputters under load?!?!?
    By Rbernsdo in forum General Chevy & GM Tech Questions
    Replies: 11
    Last: 10-23-2010, 11:37 AM
  3. 1994 tbi 350 misses under load and died
    By pondfishr in forum Chevy C/K Truck Forum
    Replies: 5
    Last: 10-14-2010, 06:08 PM
  4. 1999 5.7 1500 Sub' hesitation power loss misses
    By matthew acacia in forum Chevy Suburban Forum (GMC Yukon XL)
    Replies: 3
    Last: 05-08-2010, 01:00 PM
  5. Replies: 7
    Last: 01-03-2010, 08:40 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •