

Same problem as right before my CV snapped the last time except with no snapped CV....yet. The truck seems like it is not fully out of 4wd. Tried backing up, tried hitting actuator with a hammer with no results. I can do a burnout but when Im driving every now and then the wheel will jerk one way or the other does not feel good. Almost feels like the front wheels are fighting eachother. If I'm going perfectly straight there no problem, but any turn and im gettin the twitch. I can't deal with this anymore I think its the end of offroading for my old burb. Does this sound like actuator is bad or T-case issues?![]()
Dan
1999 GMC Sierra 2500 350 vortec
1967 Jeep M725 ambulance 230 tornado
1990 Cherokee Limited- 3 inch lift on 33's
...and every one of em has issues
If you have any questions or problems don't hesitate to send me or any other GMTC moderators a PM


Sounds like a bad CV joint. Did you replace both?
There is no way to happiness....happiness is the way.
High Desert SoCal
93 K1500 burb (personal) 350 AT 3" Lift 250K+
02 Honda Civic LX
Looking for a 1990's Miata for an engine swap




I was kinda thinking you might have to clean and repack front hubs. Mud, Water, Dirt in there? They act weird when they get dry and contaminants in there. Just a thought.
Jamie
2007 Ford E250(Work van) (Ya, Ya, shut up!)
1996 GMC Sierra SLE 1500 5.7L/4L60E
http://www.thefundumpster.com


only replaced one CV. I don't have the loud clicks like I did when the other one broke.
Dan
1999 GMC Sierra 2500 350 vortec
1967 Jeep M725 ambulance 230 tornado
1990 Cherokee Limited- 3 inch lift on 33's
...and every one of em has issues
If you have any questions or problems don't hesitate to send me or any other GMTC moderators a PM


That's kinda like replacing one wheel bearing. Sure a CV can fail prematurely especially if the boot leaks, but as a rule, they should be replaced together. I had a fwd minivan that started rumbling during acceleration in a corner. Drove it that way for months then bang it broke on the drivers side. The tranny shop was thinking transmission but a quick look with the boot off and the problem was obvious. Only replaced one side and the other was gone in less that 6 months. Keep us posted on what you find.
There is no way to happiness....happiness is the way.
High Desert SoCal
93 K1500 burb (personal) 350 AT 3" Lift 250K+
02 Honda Civic LX
Looking for a 1990's Miata for an engine swap


CV was gone and I also "blew apart" my front axle shaft. $225 for everything. I think I'm done 4 wheelin for a while I cant afford to spend that kind of money every two weeks.
Dan
1999 GMC Sierra 2500 350 vortec
1967 Jeep M725 ambulance 230 tornado
1990 Cherokee Limited- 3 inch lift on 33's
...and every one of em has issues
If you have any questions or problems don't hesitate to send me or any other GMTC moderators a PM


There is no way to happiness....happiness is the way.
High Desert SoCal
93 K1500 burb (personal) 350 AT 3" Lift 250K+
02 Honda Civic LX
Looking for a 1990's Miata for an engine swap


haha no rock crawling for the suburban. just the rut filled trails that are near my house. I don't even beat on it i dont get how I can break so much stuff.![]()
Dan
1999 GMC Sierra 2500 350 vortec
1967 Jeep M725 ambulance 230 tornado
1990 Cherokee Limited- 3 inch lift on 33's
...and every one of em has issues
If you have any questions or problems don't hesitate to send me or any other GMTC moderators a PM



CV joints do go, older the vehicle the more likely they are to go when running over potholes, 4 wheeling or not. Replace the second one and you should be good for another 200K.
Technology is great, when it Works,
And one Big Pain in the Ass When it Doesn’t.
Detroit Iron Rules, All the Rest are Just Toys.
94 GMC Burban, 5.7L (350), 4X4, Auto
86 GMC Burban, 350, 2 WD, Auto
79 GMC pickup plow truck, 400, Full time 4X4, Auto
86 Pontiac Fiero SE, 2.8L, Auto, only mid engine American car
See a Pattern yet?
15 year GM assembly line worker.
Bookmarks