Results 1 to 9 of 9
Thread: How to firm up the seats?
03-02-2012, 12:31 PM #1
How to firm up the seats?
I bought a used 2005 Silverado 2500HD with 74K miles. I knew the seat was a bit sagging when I first bought it (and used that to my advantage in negotiating). Now I'm trying to figure out what to do with it. When I drive over bumps, the seat launches me into the air. While fun, it's not the most comfortable or the safest. Any ideas on how much I can do to firm up the seat? I'll probably take it to an upholstry shop to check out, but wanted to get thoughts first. Should the springs be replaced, just add padding, ....?
The seat is full manual adjust and the truck is extended cab, so the seat belt is integrated into the seat.
03-02-2012, 12:57 PM #2
When I got my '03, I felt like I was sitting on the floor! I took the seat apart and noticed that the springs from front to back under the seat cushion (which were nothing more than 5 to 6 wires tied from the back to the front) had been cutting into the seat foam. Think of a cheese slicer here. I pulled the cushion out of the springs and cut a piece of cardboard to go between the springs and foam. I wrapped the cardboard in an old towel and re-assembled. The seat felt great after that.
The upholstery is only held on to the seat with plastic clips. there are no hog rings. you can unsnap them and pull the material off. This would be the time to toss teh covers into the washing machine. DO NOT DRY THEM, however. Let them hang on a line until dry.
Hope this helps!"It went together didn't it? Well then there has to be a way to take it apart!" - Me.
Check out my image gallery HERE.
"The true measure of a man is how he treats someone who can do him absolutely no good." ~Samuel Johnson (1709-1784)
03-02-2012, 01:13 PM #3
03-02-2012, 01:27 PM #4
Sure it does. they are the same underneath the coverings.
03-05-2012, 12:12 PM #5
03-05-2012, 02:47 PM #6
Wrap the cardboard with an old towel. That will give a little bit.
Glad it helped if even a little.
03-05-2012, 03:39 PM #7
Auto Restorer Magazine ran a "how to" article for rebuilding seats that shows how to select and carve/shape foam for putting in the seat. I can't recall the month, but you might try going on their web site and emailing them about getting a copy of that issue. It is a great magazine for anyone wanting to know how to do all sorts of work on your car, not just for restorers like me.
The article was, I believe, in the past 12 months.1994 Chevy K2500 Silverado, 454 (modified), original owner.
And other vehicles and toys.
"...If you can meet with triumph and disaster
And treat those two imposters just the same;
...you'll be a Man, my son!" Rudyard Kipling
03-05-2012, 04:56 PM #8
I'll try the towel.
Looks like this is the issue: http://www.shopanimalnetwork.com/pro...0&cid=91&mid=2 I'll see if there is anything else on the WWW, otherwise, $7 isn't too bad to buy a good article.
03-05-2012, 06:30 PM #9
It is a three part series that ends in the December 2011 issue (that one talks about the electric mechanisms in electric seats). I could not find the November issue as of this writing, but you may want to look at that issue as well. I could have sworn it had pictures of cutting that foam, and I did not see it in the October article.
By parts bot in forum Chevy Trucks For Sale eBayReplies: 0Last: 02-09-2012, 08:00 PM
By chevytruckman in forum GM PowertrainReplies: 4Last: 09-24-2010, 12:36 PM
By ChevyFan in forum The Coffee Shop ~ Chit ChatReplies: 1Last: 03-26-2009, 02:38 PM
By ChevyFan in forum The Coffee Shop ~ Chit ChatReplies: 0Last: 05-14-2007, 11:15 AM
By ChevyFan in forum The Coffee Shop ~ Chit ChatReplies: 0Last: 05-13-2007, 04:31 PM
Tags for this Thread