Results 1 to 8 of 8
Thread: TPMS question
03-02-2012, 06:40 PM #1
I just had my tires rotated. I now have a low pressure alarm for the left rear. So I stop at Sheets to put air in the tire. The pressure in the rear was at 43psi. So I check the front. It was the front tire that was low. How do the monitors know which corner they are on? Is there a way to correct this?
03-02-2012, 06:43 PM #2
the shop should have reset the tpms for you. I do not have the system but know that is a problem. I think there is a simple way to do it but dont remember.David
2004 Silverado 2500 Crew Cab 4x4, AMSOIL EA air filter, Granatelli MAF sensor, Throttle body spacer, Magnaflow exhaust (true dual to 2 in 1 out muffler), 6" ProComp lift (add a leaf and 5" superlift rear block), Bilstein shocks, 35's (Cooper Disoverer ST) and 4.10 gears, Rhino Liner, EGRUSA fender Flares and widow visors, extended stainless steel brake lines, firestone airbags w/onboard air compressor, Pioneer Avic X940BT navigation, Accel backup camera.
1960 Land Rover Series II 88
2001 Pontiac Sunfire
2013 Toyota Avalon Limited (Wife's Car)
NRA Life Member
03-02-2012, 09:07 PM #3
In your owners manual is the procedure for your tpms. On my wife's 06 H3 you turn the key a number of times then something else, then the horn blows then you go to the front left, release air for about 10 seconds the horn will blow again the go to the right front release air then so on and so on... But your owners manual has the right procedure for your vehicle. Be patient, it took me about two times to get it on the first try. A little tip remove all the valve caps so your not rushing around. Hope this helps.
03-02-2012, 09:28 PM #4
03-02-2012, 09:37 PM #5
- Join Date
- May 2011
- Myrtle Beach, SC
- Blog Entries
It should be in the owners manual but if all else fails I think you can disconnect the battery and they will reset!
(Scott) Myrtle Beach, SC
January 2012 ROTM WINNER
2011 GMC Sierra Z71 MAX 6.2 L w/ Trailering Package
Rough Country, XD Rockstars, Nitto Trail Grapplers, N Fab, Lund Genesis, Putco, Gator Grip,
Flowmaster 40 series, Diablosport InTune, Banks Ram Air CAI,
WeatherTech, AVS Aeroskin, Tow Mirrors, Upgradeyourauto.com
03-06-2012, 03:23 PM #6
- Join Date
- Mar 2012
- SE of San Antonio, TX
I got this issue on my used truck I just bought... I tried the method in the book and just couldn't get it to work. I did get on honk after the initial 2 honks but that was it... Any other tips?!? LOLJonathan - La Vernia, TX
07 Chevy Silverado 1500 Z71 LTZ
04-03-2012, 07:29 PM #7
- Join Date
- Apr 2012
If it's similar to my 2011 WT model GMC then with the truck running in park you push the odometer button until it goes from your mileage to oil life then to "Reset tire position sensors" then you hold the button in for about ten seconds until it chirps, and then it's supposedly learned the new positions. I haven't tried it yet, but that's how the dealer salesman explained it to me when I bought the truck durring pre delivery. I Hope that works for you!
04-04-2012, 08:08 AM #8
I assume that you have a NNBS truck and learning the positions of the tires is very easy. Unfortunately some of the '07 models needed the computer reflashed to make the system working proper as per the manual, but, with the activation tool it worked flawlessly.
The basic procedure is in your owner's manual and the following is the procedure for my '10 Silverado (I do not have the DIC buttons).
With the ignition on but the engine off and parking brake on, hold the LOCK and UNLOC buttons on your remote keyless entry fob until the information display says "TIRE LEARNING ACTIVE" and the horn sounds twice.
Then go to the left tire wheel and let either let out or add air for 5 seconds or until the horn beeps, once the horn beeps, then proceed to the right front and do the same until the horn beeps. Then the right rear tire and do the same until the horn beeps. The the left rear until the horn beeps twice and your done.
If you have an activation tool then use it instead of letting air in or out at each tire position until the horn beeps accordingly. You only have 2 minutes from the time that the message is displayed until the final two beeps. If you do not finish in this time you will get a malfunction light on the display until you get it right.
Do not forget to air your tires back to the correct PSI after your finished and reinstall the valve caps.
Be prepared before you set the system in relearn mode. i.e. the valve caps are already off, the compressor has a full load of air, you can access all your tires without moving the vehicle. Also you should not be within 30 feet of another vehicle that may have compatible sensors.
Activating the relearn mode may be different on your vehicle so READ your manual, but, once the relearn mode is initiated the procedure is the same.
By Harrison in forum Wheels & TiresReplies: 16Last: 05-15-2011, 06:40 PM
By davist in forum General Chevy & GM Tech QuestionsReplies: 1Last: 06-22-2010, 09:56 PM
By 1flyfisher in forum Lifted & Offroad SuspensionReplies: 11Last: 02-01-2010, 05:49 AM
By thatkidmave in forum Chevy Silverado Forum (GMC Sierra)Replies: 3Last: 10-08-2009, 04:32 PM
By navyeoseabee in forum Lifted & Offroad SuspensionReplies: 14Last: 12-08-2008, 04:45 AM
Tags for this Thread