Results 1 to 4 of 4
Thread: LED Dome lights
04-03-2012, 11:45 PM #1
LED Dome lights
LED Dome lights
- 3 LEDs your choice in color
- Resistor 47ohms is what I used
- 1/4in plastic tubing
- Soldering iron
- Remove old dome bulb
- Cut plastic tube to size of old bulb (picture below)
- Drill three holes in a row in the tube (see picture)
- Cut a slice down the back side of the tube. 180 degrees from the hole your just drilled
- Now insert the LEDs into the holed from the top of the tube, make sure the LEDs are all going the same directing. LEDs are polarized current only flows one way. You do this from the outside to make sure you spacing is correct for when you into the LEDs into the tube(see picture below)
- Fold over the (-) from one LED to the (+) of the LED next to it, do this twice so all the LEDs are connected.
- Solder the leads of the LEDS and cut off the excess leads. (see picture)
- You now need to solder the resistor onto the outside (-) LED. Try to get the resistor as close to the LED as you can, space is limited.(see picture)
- Removed the LEDs you just solder, and pry the tube open and insert the LEDS into the inside of the tube and into the holes. (sorry forgot to take this picture)
- Now all you need to do it wrap the wire of the (+) LED around the tube, and the wire of the resistor around the other part of the tube.
- You are now done! Insert the new LED bulb into the dome light.
If it does not work simple flip the bulb around again LEDs are polarized and current only goes one way. I would give prices of the LEDs and resistors but I already owned them. The plastic tubing I picked up at the hardware store for like $0.50 a foot.
If you have any questions please feel free to ask.
Soon to come: LED under dash light and LED light in the mirrors that work at running light and turn signals.2011 Silverado 1500 Z71 4x4 Crew Cab
LED Dome light
LED Floor lights
RC Leveling kit
Tow Mirrors Custom LED running/signal lights
BakFlip G2 Tonneau Cover
04-08-2012, 08:24 AM #2
Thanks, looks like a fairly easy work up.1958 Chevrolet Apache Fleetside Longbed .. 350 with a turbo 350 tranny
2010 Silverado LTZ 4X4 Z71
04-17-2012, 07:46 PM #3
Pretty easy and cheap, you can get LEDs for like 10-20 cents and resistors are like 10 cents each depending on where you get them. Best part is you can use any color you want without is costing you an arm and a leg. Just make sure you use a high enough resistor for your LED or you will burn through them pretty quick.
05-06-2013, 04:10 PM #4
what size led and wattage2005 Chevy Silverado 1500HD 6.0 BBK headers,Cold air intake, Flowmaster cat-back, Diablo Trinity tuner, 22" KMC Rockstar Cooper ATZ, Kenwood DNX-9980HD indash, 2 Kenwood XR-W10F under back seat, Kicker 11DX10001, Kenwood KAC-7205, Polk Audio DXi6500 6.5"Component Speaker System front and back, Smoked out lights, 12K Hid's HI/Lo. Code Alarm W/remote start.
By Jaele in forum Lighting DiscussionReplies: 17Last: 04-25-2012, 09:16 PM
By AMac in forum GM Electrical TechReplies: 8Last: 03-09-2012, 10:43 PM
By mamaza in forum GM Electrical TechReplies: 8Last: 03-28-2010, 08:13 PM
By SoundZman in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 4Last: 04-21-2009, 09:39 PM
By Black Chevy in forum Audio, Video & Gadget TechReplies: 1Last: 03-02-2009, 06:36 AM
Tags for this Thread