Results 11 to 20 of 36
05-17-2012, 03:08 PM #11
You can't print a large format schematic from a laptop. And you can't drop a laptop on a concrete floor, pick it up and keep reading. Nor can you spill a cup of hot coffee on it and just wipe it off.1994 Chevy K2500 Silverado, 454 (modified), original owner.
And other vehicles and toys.
"...If you can meet with triumph and disaster
And treat those two imposters just the same;
...you'll be a Man, my son!" Rudyard Kipling
05-17-2012, 04:14 PM #12David
2004 Silverado 2500 Crew Cab 4x4, AMSOIL EA air filter, Granatelli MAF sensor, Throttle body spacer, Magnaflow exhaust (true dual to 2 in 1 out muffler), 6" ProComp lift (add a leaf and 5" superlift rear block), Bilstein shocks, 35's (Cooper Disoverer ST) and 4.10 gears, Rhino Liner, EGRUSA fender Flares and widow visors, extended stainless steel brake lines, firestone airbags w/onboard air compressor, Pioneer Avic X940BT navigation, Accel backup camera.
1960 Land Rover Series II 88
2001 Pontiac Sunfire
2013 Toyota Avalon Limited (Wife's Car)
NRA Life Member
01-01-2013, 01:36 PM #13Minneapolis area - 1997 K2500 regular cab long bed + 8.5' Western Unimount plow + modified transmission + 2nd battery + modified camper charge circuit + 1971 Cayo camper -and- 2004 4x4 Suburban 2500 8.1 + Maxbrake controller + 2nd battery + modified trailer charge circuit + Reese receiver, pulls 30' Airstream trailer
01-01-2013, 02:28 PM #14
01-01-2013, 10:02 PM #15
In my shop, I "take care of" tools. If it can't survive a three to four foot drop to a concrete floor, it doesn't belong in a shop. If you can't spill coffee on it, it is worthless. If it does not withstand an occasional size 12 1/2, 200 lb foot print on it, it doesn't belong out in my work shop. There's a place for my laptop and it isn't in my shop.
01-02-2013, 12:48 AM #16
Not everything in a shop has to be super rugged and, in fact, if you take care of things then you have no need to worry about spilling coffee on them or dropping them -- specifically because you take care of them.
The clock on the wall in my shop can't survive a three to four foot fall or a coffee spill, but it definitely belongs in my shop and isn't worthless. I'd be very worried about the integrity of my air compressor and air tank if either fell four feet onto a concrete floor. I'm not terribly sure if my Dremel would survive a four foot fall and a coffee spill would probably kill it, yet it's not "worthless". My chain saw is also something I'd worry about if it fell four feet, as the fuel tank might crack, the bar might be bent, or a host of other issues might occur.
Plainly put, I absolutely do not agree with your 'logic'. There are plenty of things in a shop (especially my own) that belong there even if they can't survive a 3-4 foot drop onto concrete or live through a coffee spill. Your shop must be full of rakes, shovels, and hand tools ... and completely devoid of electric power tools ... given that most electric power tools won't live through a coffee spill and, thus, per your comment they are supposedly "worthless".
01-02-2013, 04:21 AM #17
- Join Date
- Nov 2009
- San Diego, California, United States
- Blog Entries
Surrealone hit it out of the park! I use both but I was very disapointed when on my last coolant flush the chilton manual was completely different than my truck. I rely on the web now but the book is a good backup (for some repairs). Yes, I have the right book for my truck.
01-02-2013, 06:46 AM #18
- Join Date
- Dec 2011
- Blog Entries
When I did my radiator replacement I had the Clinton/Haynes manual and prints out from conversations on this site so I had the advice of my friends. I believe that using both the internet and the manual is the best any to do it. Online you can find better diagrams and in person explanations while the manual is cut and dry and doesn't always have all the visuals you need.
I rarely bring my laptop in the garage to work but always have my phone. Yes my DROID⁴ is built like a rock but water/oil would kill it. I use my phone to take and view pictures and check info on this site. There are also shop lights we all use that may survive a drop, if the bulb doesn't break, but water would kill in a second.
What belongs in a shop is the tools YOU think you need, not always what is the norm.
1996 Chevy Tahoe LT 5.7L V8 4X4 205,000+ miles. Built proudly at Janesville Assembly in Janesville, Wisconsin
Basic mods: Lights all over, bunch of electrical work, and a couple cooling mods.
Check out my other mods in My Garage: http://www.gmtruckclub.com/forum/sho...t-Tahoe-4-Door
01-02-2013, 07:46 AM #19
I have found that for most of the work I am try to do to the truck myself these days requires a little more detail than what their outdated $24.95 general purpose manual's offer so I don't waste my money anymore.
I take an ipad for diagrams under the truck now and use my android phone for taking photo's for comparisons.
The "paper" manual is officially done for me, it makes no sense.
If they would sell me a full tear down and rebuild manual for $24.95 with full electrical break outs (not engineering diagrams) but details about where the harnesses are weeded through the firewall and where all the connections go, etc. That might be of some value.
01-02-2013, 01:06 PM #20
Would this resolve the question asked in this thread? No. So I suggest you start a new thread where you list your items and request replies to see if anyone out there has stuff that breaks like (apparently) yours break. I won't have the time to take a look.
The question posited was whether electronic records have replaced printed material for automotive service manuals. If by this one assumes that more people use one or the other, I don't think they have. If we consider the proliferation of electronic record keeping in medicine and law and municipal operations, one can make a strong argument that eventually libraries may not have books any more, and perhaps there will be more people with electronic service manuals than printed media. But the time for that is beyond what anyone can presently predict.
My point is simply this: compared to a laptop or a pc, which is needed to read the CD rom or download of an electronic manual, a book does not cost much, does not require 120 VAC or a battery, does not require a monitor or screen, does not require an operating system, does not get viruses and malware you have to remove, does not require internet service, does not require software upgrades or patches, does not require security software, does not get junk mail, does not require expensive repairs, and if you drop it from a table or a ladder or the back of your truck, it does not break. Yes, and you can also spill liquids on it and it only warps the pages a bit. In fact, if you threw a printed service manual out the window of your car on the freeway and stopped to go back and get it, you can still use it.
When you find a laptop that can meet that criteria, get back to me. When I have some spare time, I will take a look at it. I use a laptop. I have a couple of CD rom manuals, but I rarely use them. And I use a keypad cover on my laptop so I can spill coffee on it, but I still don't use it in my garage. If you love your laptop in your garage, I suggest you write a letter to Microsoft, Apple, Intel, Asus, Seagate or Western Digital and tell them. I am sure they will appreciate the endorsement.
And if you really have a chain saw that can't take a 3-4 foot drop, I suggest you spend some of that free time to earn some extra money and buy a good chain saw. I have a Stihl chainsaw and it can take that abuse.
By BowTieFan1 in forum Chevy Silverado Forum (GMC Sierra)Replies: 6Last: 07-01-2011, 02:29 PM
By zamjohn in forum Announcements & FeedbackReplies: 2Last: 10-22-2009, 10:23 PM
By dwill3015 in forum General Chevy & GM Tech QuestionsReplies: 60Last: 09-30-2009, 09:27 PM
By bowwow in forum Member IntroductionsReplies: 9Last: 08-26-2009, 11:08 PM
Tags for this Thread