Results 21 to 30 of 36
01-02-2013, 02:47 PM #21
I just found one in ten words or less:
- - - Updated - - -
Actually I stand corrected.... you can print anything you want up to 128 inches by how ever long the roll of paper is with this one.:
This 128 inch roll-fed printer uses eco-friendly aqueous ink for a direct dye sublimation printing and comes with a customization kit that allows you to add a ditch for ink runoff to prevent unwanted penetration of more porous materials such as mesh or flag. The Mimaki320DS has a staggered head array, utilizing four printheads for high speed printing. The printer also comes with Mimakiís automatic nozzle failure detection, uninterrupted ink supply system, Rasterlink Pro III RIP, and automatic registration for doublesided prints. Made for the flag, banner, trade show fabric graphics, P-O-P, and soft signage markets this is a great printer with a max 720◊1440 dpi resolution that can print 645 sq ft per hour.
Is 128 inches big enough for your schematics?
01-02-2013, 03:06 PM #22
$3,960.00. I don't think that is a viable option for any homeowner except the richest out there. How much is a manual? ten-twenty bucks on eBay?
http://configure.us.dell.com/dellsto...acd=s_pla_SO291994 Chevy K2500 Silverado, 454 (modified), original owner.
And other vehicles and toys.
"...If you can meet with triumph and disaster
And treat those two imposters just the same;
...you'll be a Man, my son!" Rudyard Kipling
01-02-2013, 03:17 PM #23
- Join Date
- Dec 2011
- Blog Entries
I wouldn't say richest, but its not something an DIYer needs. Really if I needed I could do prints 36" wide on my dads full color plotter, but that would be a waste of time if I can find a pic that prints well on 8.5x11 or is in a manual. I think using both is the most beneficial. Use the manual for an overview and so basic pics then ask on line or look up and get more pics and expanded instructions.
Some times manuals can get you through a project with out any problems, but sometimes you need more than just "remove the three bolts then pull the part off" Because a manual wont tell you that to get to those three bolts you need to have magical hands. I have had times when using a manual where it just didn't elaborate on very difficult processes, but friends on the site did.
1996 Chevy Tahoe LT 5.7L V8 4X4 202,000+ miles. Built proudly at Janesville Assembly in Janesville, Wisconsin
Basic mods: Lights all over, bunch of electrical work, and a couple cooling mods.
Check out my other mods in My Garage: http://www.gmtruckclub.com/forum/sho...t-Tahoe-4-Door
01-02-2013, 03:22 PM #24
Web forums for vehicles specific to what you have are a great source for pictorial instructions for installations that are not covered in a manual of any type, and this is the electronic source I use for aftermarket installations on some vehicles I own where I can find the thread for it and someone has been kind enough to put all the pictures. I needed to install a stereo in a car dash that at the time had no domestically available dash kit, and someone put a multi page instruction thread on an Infiniti forum for doing it, complete with desoldering and re-installation instructions for a button that had to be put on the replacement dash kit (they provided the source in Japan for the dash kit too). But I still use the OEM manuals for most procedures.
01-02-2013, 04:10 PM #25
Well, that is why a $599 ipad/android tablet with a 10 inch screen and wireless to a 13x19 inch printer which will only set you back maybe $199 (printer) will be fine for printing out anything you need to take to the vehicle you are working on. That is allot less than a $3700 laptop and $30,000 plotter.
And I am not so much worried about oil getting on the ipad screen because you would just wipe it off. Now I would not stick an ipad in a 5 gallon pail of oil. If you do that you really should not be working on your truck in the first place.
Oh and the android tablet or ipad can also be connected via blue tooth to the OBDII port in the truck so you can get real time diagnostics while you are under it.
Last edited by PantheraUncia; 01-02-2013 at 04:14 PM. Reason: Added OBT II info
01-02-2013, 06:27 PM #26
I think it would make a great start to a new thread on what to buy to use in the shop if you are not a hard copy manual person such as myself.
(I still believe at this juncture that as far as the original question of this thread, there are still more people using books than electronic media, in the CONSUMER realm. Repair shops, even small ones, have mostly gone to a monthly service of electronic research to get the data they need to work on vehicles. however.)
01-02-2013, 10:28 PM #27
While I do love GMTC and all of the people who have helped me in the past, I did put a Silverado repair manual on my Christmas list; yes Santa brought it
01-02-2013, 10:34 PM #28
- Join Date
- Dec 2011
- Blog Entries
Personally I want the GM service manual for my truck, its two books and costs $300 but has everything!!!!!!
01-02-2013, 11:46 PM #29
01-03-2013, 08:13 AM #30
By BowTieFan1 in forum Chevy Silverado Forum (GMC Sierra)Replies: 6Last Post: 07-01-2011, 03:29 PM
By zamjohn in forum Announcements & FeedbackReplies: 2Last Post: 10-22-2009, 11:23 PM
By dwill3015 in forum General Chevy & GM Tech QuestionsReplies: 60Last Post: 09-30-2009, 10:27 PM
By bowwow in forum Member IntroductionsReplies: 9Last Post: 08-27-2009, 12:08 AM