Results 1 to 10 of 18
06-08-2012, 02:55 AM #1
On Board Air (OBA) compressor & tank mounting locations?
Has anyone done on board air (OBA) -without- placing the compressor or tank in the engine comparment, cab, truck box, or bed? If so, what size tank did you use and where did you mount it? How about the compressor? If using Viair, which kit?
Inquiring minds want to know!
06-08-2012, 11:23 AM #2
- Join Date
- Mar 2007
- Grand Prairie, Texas
- Blog Entries
I've got air systems on two of my trucks, the Tacoma and the Rock Crawler, they both use 4 gl suasage tanks mounted on the outside of the frame rails.
Since the crawler see's a lot of beating and banging I built a cage to go around the tanks, that system uses 2 Schedule 40 PVC tanks, the sched 40 takes vibration and beating a little better.
The tank on the Tacoma is from Western Air Industries (I dont think their in buisness anymore) and came with 3 welded in bungs, inlet, outlet, pressure gauge.
It's much easier to find a spot on the outside of the rails than the inside. Both systems are plumbed with Tephlon braided hoses to cut down on vibration, hard lines tend to crack after a while. The system on the Tacoma is filled by a VIA Air 350C and has the storage tank and also runs the front ARB locker.
The system on the crawler runs a VIA Air 650C and has two storage tanks and maintains 4 Firestone 500 airbags for the suspension.
06-08-2012, 11:59 AM #3
06-08-2012, 12:29 PM #4
You're not leaving many options for mounting locations! Haha. No really, my dad has 2 three gallon tanks mounted on the outside of his frame rail (passenger side), underneath the cab area on his 2006, so I would think you would have plenty of room there. Not sure of the specs on the Viair tanks...his were some we ordered online years ago. As for the compressor, his is mounted above the wheelwell in the bed, but you should have room along the frame rail also, being that your truck is a longbed. If I were you, I'd fabricate a bracket to mount the compressor upright, so moisture doesn't collect in the cylinder head.
My big tank and compressors are in the bed, with 2 three gallon tanks on the inside of the frame rails, in the spare tire area. (The tire was relocated.) I didn't have as much room underneath along the sides, or I would have possibly put the tanks there.-Sal
2008 Silverado 1500 LT 5.3L Crew Cab
Desert Brown Metallic
Century top, Yakima roof rack, 2.5" front lift, Readylift 3" rear blocks, Line-x bedliner, step bars, AVS vent visors, Weathertech floor liners, door sill guards, power tailgate lock, tailgate damper, KC light bar w/ PIAA 525s, rear mini-light bar, rear LED reverse/utility lights, dual batteries (Cole Hersee isolator), DIC upgrade, 20" GM wheels, Cooper Discoverer A/T3s, 26 gal. onboard air (twin Viair 480Cs), Nathan Airchime K3HA / Old cast 2nd Gen. P3 Horns, Graham White valve, bell
Past Chevys: 1985 S-10 ext.cab, 1963 BelAir sedan
06-08-2012, 01:02 PM #5
Fabrication of a bracket isn't my forte as I can't weld and don't have a cutting torch. I can likely spec something and get it done, though. I'll scout the suggested locations this weekend and take some measurements. I will say I'm a little worried about -outside- the frame rail as it could be ugly if someone side swipes me ... so I'll also be scouting -inside- the frame rail. I presume self-tapping bolts are how I'd need to go for mounts to the frame rail?
06-08-2012, 05:31 PM #6
i dont know that id go taping into the frame rails, dont want to weaken things. id look into some sort of compression clamp or u bolt to attach things. not sure how much clearence you have in the long bed, maybe in front of the cross tube that is in front of the spare tire mount. Maybe use the cross tube itself? weld the ends shut, tap for some air lines and a water drain.... now thats a thought.
2011 GMC Sierra SLE 5.3 Z71 4X4 Stealth Gray Metallic / 2004 Chevy Impala LS 3.8 Cappuccino
Tow mirrors - Diablew Tuned - Flowmaster Regular 40 - Ready Lift 2.5' lift - BFG LT A/T K/Os - Carr Light Wing - TruckLite LED lights - Optima Red Top - 50% Front Window Tint - Line-X bedliner - Airaid MIT - Tekonsha P2 - ARS Billet Grill - Fia custom fit seat covers
06-08-2012, 05:39 PM #7
I'm thinking it's going to be a York EDC rather than an electric unit. The CFM are looking better and better to me from one. I'm also liking Viair less and less as I do my homework ... because aside from the compressors they're really spendy for what you get. Guys with bagged and lowered trucks who have them seem to exhibit buyer's remorse in other forums ... and want to go EDC for the reliability and CFM.
If I go down the EDC path it means a custom bracket needs to be made to mount the York. 07XCSB is providing guidance on possible approachs, as he's got some OBA experience and it's all new to me. This one's going to be fun (I'll learn a lot) ... and slow to complete (because I'm way out of my element/comfort zone.)
Last edited by SurrealOne; 06-08-2012 at 06:15 PM.
06-08-2012, 05:47 PM #8
advice on welding. start with wire feed, its more forgiving and easier to learn on then stick or torch welding with fill rod. i wont type it all out here, you can find out more then I can begin to cover online. just start small, on some scrap metal that you dont care about messing up. after doing some welds, you will get a feel for it. just dont get discouraged. sometimes even crappy looking welds will hold just fine.
06-08-2012, 05:58 PM #9
- Join Date
- Apr 2009
- Columbia Falls, Montana, United States
- Blog Entries
Keep us posted on the progress, Surreal. I am also interested in adding in an OBA, but have been considering just getting one of those cheap pumps that you hook up to your battery for that kind of stuff, since it'd just be for when I air up or down.2005 Chevy Silverado W/T
4X4|4.8 with some mods (has only slightly more pull than a 5.3)|Auto|4 door ex cab|Cooper Discoverer AT/3's in 285-75/17's on Helo 842's|Cooper Discover M+S 265-75/17's on Devino DV349's|Flowmaster 40 Single in Dual out with custom bent pipe from the end of the cats back|2" Procomp leveling kit|Custom made center console|Custom dyno tunes|Air Raid CAI|Air Raid Throttle Body Spacer|Apex brand topper|Kenwood Head Unit with Kenwood speakers|Painted mirrors/grille|Debadged except front emblem|Bilsteins front and rear
Planned mods not in order
2 inch lift|Custom front/rear bumper|hitch tire carrier|roof basket on topper, bars on cab|finish center console build|install Midland CB|Power options|Tint|Custom made raised bed in the bed of the truck|Lund LunarVisor
Also have a 1992 Ford Ranger with a lot of stuff done to it. Currently waiting for a bit of a rebuild.
"The only woman I'm pimping from now on is Sweet Lady Propane. And I'm tricking her out all over this town."
06-08-2012, 06:23 PM #10
Well, another consideration is cost. A junked York compressor will run about 35-75 bucks (US) depending on who pulls it and where. That's a big compressor (compared to electrics) for not much money. DIY EDC should be a heck of a lot cheaper AND better than electric. The drawback to it is maintenance, as EDC's need to be lubricated. They have an oil sump though ... and it can't be hard to fabricate a reservoir with a dipstick. That's what has me looking at EDC's -- better airflow/output ... for less money if you DIY.
I -might- have found a bolt-on for our trucks (99-04), but it's questionable, as they claim it's bolt-on for 99-04 Silvy's and Sierras. I've had issues with vendors claiming 1:1 compatibility among those years, before, so I pinged them to be sure. Waiting for results. If it fits my truck, that kit is right about 1k -- which is absurd compared to DIY costs.
By bzboardco in forum Chevy C/K Truck ForumReplies: 2Last: 01-08-2010, 06:54 PM
By RussellFidel in forum Audio, Video & Gadget TechReplies: 6Last: 10-22-2009, 09:35 PM
By 4wd-burban in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 5Last: 03-09-2007, 08:59 AM
By Crawdaddy in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 12Last: 03-05-2007, 07:22 PM
Tags for this Thread