GM Truck Club
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 7 of 7
  1. #1

    Default ABS module removal

    I am about to tackle the above today so i can send the module for repair. I cleaned all four torx head screws from dirt build up and successfully loosened them. I wa able to remove the power connector but struggled a bit removing the bigger connecter. How is this connector locked to the female end? I cannot seem to find the locking tab.

    I am talking about the mass connector in the picture i borrowed below.
    Click image for larger version. 

Name:	ABS module.jpg 
Views:	1027 
Size:	53.9 KB 
ID:	40526
    2011 Chevy Silverado LT 4WD 30k miles
    2001 Suburban 2WD, 5.3, V8 185k miles
    1993 964
    1996 318TI

  2. Likes FordBoy33 liked this post
  3. #2


    I pulled the ABS module today. The mass connector has a red tab that you need to pull down to release the connector. Once I got it out, I followed the diy step by step and opened the top cover by slicing the RTV along the parting line. The top cover is held in place by six (6) T8 torx screws.
    Once opened, I saw all the solder connections that were suspect especially the ones on the relays. Reflowed the solder joints and sealed it back up.
    Test drove and the ABS Brake lights did not come back anymore. Been driving for the last 30 miles and still OFF.
    I saved the $150 repair cost that Module master charges/

    Thanks GMTC for the step by step diy.

  4. #3


    ABS and Brakes lights on instrument panel still OFF after 100 miles. I believe my ABS module is fixed.

    Now I can use the savings on new brake pads and rotor resurface.

  5. #4


    Great, need to do this on my 2001 Sub, also.

  6. #5


    It has been 10k miles since the ABS repair and still no ABS faults on the dash.

  7. #6


    Great. Was this on your 2001 Suburban? If so, what was the behavior? On mine, most of the time you drive the car, the ABS and brake lights both come on soon after getting underway, but sometimes you can drive for miles/hours without them coming on. I do notice that when the lights are ON, I can lock up the rear wheels with moderately heavy braking.

    And where are the full DIY steps you mentioned? I searched on this forum and don't see it. I did find a YouTube video where the guy is soldering some connections.


  8. #7


    Do a search here and you will find it.

    Here is the Youtube link too:

Similar Threads

  1. BCM module?
    By Mr. Sierra in forum GM Powertrain
    Replies: 0
    Last: 05-26-2011, 04:30 AM
  2. Pac module..
    By montyss in forum Audio & Video Classifieds
    Replies: 0
    Last: 02-22-2011, 08:30 PM
  3. ABS module fix
    By FireRed in forum Lifted & Offroad Suspension
    Replies: 3
    Last: 10-23-2010, 08:46 PM
  4. Replies: 4
    Last: 09-19-2010, 06:16 PM
  5. light control module or keyless entry module
    By fd8215 in forum General Chevy & GM Tech Questions
    Replies: 1
    Last: 05-01-2009, 08:45 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts